Abstract:Recently, various miniaturized electronic systems and the rapid increase in power density of microelectronic devices have created additional requirements for micro-scale heat dissipation technology. To dissipate heat in a micro-scale region efficiently, several creative cooling methods for high heat flux dissipation have been designed on the order of 1000 W/cm(2). Due to its high surface-to-volume ratio, the microchannel heat sink has become the most popular one among emerging technologies and an effective tool for high heat flux thermal management. Nevertheless, in common electronic microchannel cooling systems, the traditional parallel microchannel causes a dramatic pressure loss along channel length. In this regard, the manifold microchannel heat sink cooling technology becomes promising with its high heat dissipation potential and moderate pressure drop penalty. The shortened effective flow length compared with the traditional microchannel provides a smaller pressure drop and delays the onset of the critical-heat-flux point. However, while a number of numerical and experimental studies have been conducted for the single-phase flow in the manifold microchannel, two-phase flow boiling in this kind of channel is not widely employed because of its issues with flow pattern prediction. This work develops a new solver based on open source software OpenFOAM to perform the transient process of subcooled flow boiling in the manifold microchannel heat sink. Additionally, heat transfer in the silicon substrate is considered to improve the accuracy of simulation. Similar to single-phase flow simulation for the manifold microchannel, a unit cell model extracted from the whole cooling plate is employed for the two-phase boiling flow to avoid huge computational costs. Through several reasonable assumptions, the symmetry boundary condition is applied on four lateral surfaces in the unit cell, while uniform heat flux is adopted on the bottom wall. A uniform inlet velocity boundary estimated from the total volume flow rate condition is coupled with a fixed temperature value of 7 degrees C lower than saturation temperature. After the mesh independence test, the self-programming solver and numerical methods are validated by comparing numerical results with experimental data. It is determined that the boiling curve obtained by the empirical rate phase-change model with parameters r(1)=r(v)=100 agrees well with experimental results. Furthermore, heat transfer and pressure drop performance differences are caused by microchannel width w(c) and fin width w(f). In comparison to sample A (w(c)=w(f)=15 mu m), decreasing wc and wf simultaneously leads to lower average wall temperature of the heated surface; the channel pressure drop between inlet and outlet surfaces rises dramatically when the widths decrease. When the total number of microchannels in the manifold microchannel cooling plate remains unchanged, increasing wc results in a decreased wf. Based on experimental results, heat sink sample C shows that the pressure loss can be considerably reduced under the premise of sacrificing a small degree of heat transfer performance, which can be attributed to the increased microchannel hydraulic diameter. The manifold microchannel heat sink with w(c)>w(f) is recommended for practical application due to lower pressure loss and average temperature variation.

Simulation of fluid flow and heat transfer in microchannel cooling for LTCC electronic packages

Microchannel water cooling for LTCC based microsystems

Fluid Flow and Heat Transfer Characteristics of Liquid Cooling Microchannels in LTCC Multilayered Packaging Substrate

Heat transfer performance of microchannels in LTCC substrate

A 3D Micro-Channel Cooling System Embedded in LTCC Packaging Substrate.

Design and Analysis of Microchannel for the Thermal Management of Multi-stacked LTCC Laminates

Simulation on Heat Transfer of Microchannels and Thermal Vias for High Power Electronic Packages

Thermal Analysis on Active Heat Dissipation Design with Embedded Flow Channels for Flexible Electronic Devices

Experimental and Numerical Study of Transient Electronic Chip Cooling by Liquid Flow in Microchannel Heat Sinks

Computational Study and Optimization of Laminar Heat Transfer and Pressure Loss of Double-Layer Microchannels for Chip Liquid Cooling

Experimental and Numerical Studies of Fluid Flow Confined in Microchannel

Simulation of Flow and Heat Transfer in Micro Couette Flow

Numerical Analysis of Microchannels Designed for Heat Sinks

Conjugate Heat Transfer in Fractal Tree-Like Channels Network Heat Sink for High-Speed Motorized Spindle Cooling

A study of the heat transfer characteristics of the micro-channel heat sink

The Investigation Of 3d Embedded Microchannel Networks For 3d Ic Cooling, Vacuum Packaging And Thz Passive Device Applications

Numerical Simulation of Subcooled Flow Boiling in a Manifold Microchannel Heat Sink

Investigation of cooling performance of micro-channel structure embedded in LTCC substrate for 3D micro-system

Numerical Simulation on Channel Selection for Liquid Metal Cooling Device in Space Environment

Numerical Analysis of Flow Boiling Characteristics of a Single Channel Heat Sink Subjected to Multiple Heat Sources

Numerical simulation on variable width multi-channels heat sinks with non-uniform heat source