Abstract:Recently, various miniaturized electronic systems and the rapid increase in power density of microelectronic devices have created additional requirements for micro-scale heat dissipation technology. To dissipate heat in a micro-scale region efficiently, several creative cooling methods for high heat flux dissipation have been designed on the order of 1000 W/cm(2). Due to its high surface-to-volume ratio, the microchannel heat sink has become the most popular one among emerging technologies and an effective tool for high heat flux thermal management. Nevertheless, in common electronic microchannel cooling systems, the traditional parallel microchannel causes a dramatic pressure loss along channel length. In this regard, the manifold microchannel heat sink cooling technology becomes promising with its high heat dissipation potential and moderate pressure drop penalty. The shortened effective flow length compared with the traditional microchannel provides a smaller pressure drop and delays the onset of the critical-heat-flux point. However, while a number of numerical and experimental studies have been conducted for the single-phase flow in the manifold microchannel, two-phase flow boiling in this kind of channel is not widely employed because of its issues with flow pattern prediction. This work develops a new solver based on open source software OpenFOAM to perform the transient process of subcooled flow boiling in the manifold microchannel heat sink. Additionally, heat transfer in the silicon substrate is considered to improve the accuracy of simulation. Similar to single-phase flow simulation for the manifold microchannel, a unit cell model extracted from the whole cooling plate is employed for the two-phase boiling flow to avoid huge computational costs. Through several reasonable assumptions, the symmetry boundary condition is applied on four lateral surfaces in the unit cell, while uniform heat flux is adopted on the bottom wall. A uniform inlet velocity boundary estimated from the total volume flow rate condition is coupled with a fixed temperature value of 7 degrees C lower than saturation temperature. After the mesh independence test, the self-programming solver and numerical methods are validated by comparing numerical results with experimental data. It is determined that the boiling curve obtained by the empirical rate phase-change model with parameters r(1)=r(v)=100 agrees well with experimental results. Furthermore, heat transfer and pressure drop performance differences are caused by microchannel width w(c) and fin width w(f). In comparison to sample A (w(c)=w(f)=15 mu m), decreasing wc and wf simultaneously leads to lower average wall temperature of the heated surface; the channel pressure drop between inlet and outlet surfaces rises dramatically when the widths decrease. When the total number of microchannels in the manifold microchannel cooling plate remains unchanged, increasing wc results in a decreased wf. Based on experimental results, heat sink sample C shows that the pressure loss can be considerably reduced under the premise of sacrificing a small degree of heat transfer performance, which can be attributed to the increased microchannel hydraulic diameter. The manifold microchannel heat sink with w(c)>w(f) is recommended for practical application due to lower pressure loss and average temperature variation.

Experimental and Numerical Study of Transient Electronic Chip Cooling by Liquid Flow in Microchannel Heat Sinks

An Experimental Study of Microchannel and Micro-Pin-Fin Based On-Chip Cooling Systems with Silicon-to-Silicon Direct Bonding.

Theoretical and Experimental Research on Flow Boiling Heat Transfer in Microchannels for IGBT Modules

Two-phase Flow Oscillation and Distribution in Parallel Channels During R1233zd(E) Subcooled Flow Boiling: A Numerical Study

Simulation of fluid flow and heat transfer in microchannel cooling for LTCC electronic packages

Numerical evaluation on the heat dissipation capability of liquid metal based chip cooling device

Numerical Analysis of Flow Boiling Characteristics of a Single Channel Heat Sink Subjected to Multiple Heat Sources

Numerical Simulation of Subcooled Flow Boiling in a Manifold Microchannel Heat Sink

Numerical simulation of microchannel heat exchanger using CFD

Experimental study of flow boiling in microchannel heat sink enhanced with partially in-line pin fins fence arrangement

Experimental and numerical study of structural parameters on the heat transfer performance of submerged cooling system

Hybrid Mini/Micro-Channel Heat Sink Using Liquid Metal and Water As Coolants

Study on the performance of a miniscale channel heat sink with Y-shaped unit channels based on entransy analysis

Numerical simulation study of thermal and hydraulic characteristics of laminar flow in microchannel heat sink with water droplet cavities and different rib columns

Numerical Investigation Of Flow Boiling In A Manifold Microchannel Heat Sink With Conjugate Heat Transfer

Numerical Simulation and Optimization of Microchannel Heat Sink Combined With Jet Impingement

Computational Study and Optimization of Laminar Heat Transfer and Pressure Loss of Double-Layer Microchannels for Chip Liquid Cooling

Experimental and Numerical Studies of Fluid Flow Confined in Microchannel

Experimental Investigation of Liquid Metal Alloy Based Mini-Channel Heat Exchanger for High Power Electronic Devices

A study of the heat transfer characteristics of the micro-channel heat sink

Numerical Study of Enhanced Heat Transfer of MicroChannel Heat Sink with Nanofluids