Abstract:It is highly desired to efficiently dissipate the high heat flux generated in electronics. A novel hybrid microchannel heat sink combining manifold with secondary oblique channels (MMC-SOC) has been proposed and studied numerically in our previous work. The current study conducts the fabrication and experimental test of the hybrid microchannel heat sink using dielectric fluid HFE-7100. The volume flow rate qv ranges from 211 to 580 mL/min, with channel Reynolds numbers between 278 and 905 for heat fluxes q'' = 20, 25, 30 and 35 W/cm2. The results indicate that the MMC-SOC heat sink can simultaneously reduce the thermal resistance Rt and pressure drop ∆P. For heat sinks with channel height Hc = 60 μm, an 11% reduction in ∆P and a 24% reduction in Rt are obtained compared to conventional manifold microchannel (MMC) heat sink for qv = 580 mL/min and q'' = 20 W/cm2. As qv increases, the ratio (Rt/Rt0) becomes smaller and (∆P/∆P0) becomes larger, which indicates an enhanced ability of reducing Rt and a suppressed ability of reducing ∆P. For the maximum qv = 580 mL/min and q'' = 35 W/cm2, the MMC-SOC heat sink can maintain a maximum chip temperature of 53 °C with a pressure drop of only 3.77 kPa. Moreover, the proposed MMC-SOC heat sink has a lower pressure drop compared to MMC heat sink owing to a reasonable design, even though the Reynolds number of the MMC-SOC heat sink reaches up to 883. This provides a very promising scheme for safe and efficient single-phase microchannel cooling used in the thermal management of electronics with high heat flux. In addition, the ratio (Rt/Rt0) will increase with increasing heat flux and increasing the flow rate becomes an effective way to further reduce the chip surface temperature at operating conditions with higher heat flux.

Design, integration and performance analysis of a lid-integral microchannel cooling module for high-power chip

An Experimental Study of Microchannel and Micro-Pin-Fin Based On-Chip Cooling Systems with Silicon-to-Silicon Direct Bonding.

Embedded microfluidic cooling with compact double H type manifold microchannels for large-area high-power chips

Flow Boiling of HFE-7100 for Cooling Multi-Chip Modules Using Manifold Microchannels

Embedded Cooling Method with Monolithic Dual-Layer Microchannel Cold Plate for High-Power Chips

A Miniaturized Integrated System for Embedded Microchannel Cooling with Manifolds

Heat Dissipation Characteristics of a Jetting Staggered Microchannel for Cooling a Large-area High-performance SOC Chip

Investigation of Z-type Manifold Microchannel Cooling for Ultra-High Heat Flux Dissipation in Power Electronic Devices

Experimental study on single-phase hybrid microchannel cooling using HFE-7100 for liquid-cooled chips

Hybrid Mini/Micro-Channel Heat Sink Using Liquid Metal and Water As Coolants

Numerical Study on Hybrid Discontinuous Microchannel Heat Sink Combining Manifold with Pin Fins (DMC-MPF) for High Power Electronic Device

Experimental study of embedded manifold staggered pin-fin microchannel heat sink

Embedded Micro-Pin Fin Heat Sink of Two-Phase Liquid Cooling for High Heat Flux 3D ICs

A universal high-efficiency cooling structure for high-power integrated circuits☆

Topologically optimized manifold microchannel heat sink with extreme cooling performance for high heat flux cooling of electronics

Case-embedded cooling for high heat flux microwave multi-chip array

Integrated Manifold Microchannels and Near-Junction Cooling for Enhanced Thermal Management in 3D Heterogeneous Packaging Technology

Design. Fabrication, and Test of an Embedded Si-Glass Microchannel Heat Sink for High-power RF Application

Jet Microchannel with Sawtooth Wall for Efficient Cooling of High-Power Electronics

Design of Microchannel Heat Sink Using Topology Optimization for High Power Modules Cooling

Suitability of Embedded Liquid Cooling and Heat Generation for Chips