Abstract:Thermal management is one of the main challenges for the future of electronics<a href="#ref-CR1">1</a>,<a href="#ref-CR2">2</a>,<a href="#ref-CR3">3</a>,<a href="#ref-CR4">4</a>,<a href="/articles/s41586-020-2666-1#ref-CR5">5</a>. With the ever-increasing rate of data generation and communication, as well as the constant push to reduce the size and costs of industrial converter systems, the power density of electronics has risen<a href="/articles/s41586-020-2666-1#ref-CR6">6</a>. Consequently, cooling, with its enormous energy and water consumption, has an increasingly large environmental impact<a href="/articles/s41586-020-2666-1#ref-CR7">7</a>,<a href="/articles/s41586-020-2666-1#ref-CR8">8</a>, and new technologies are needed to extract the heat in a more sustainable way—that is, requiring less water and energy<a href="/articles/s41586-020-2666-1#ref-CR9">9</a>. Embedding liquid cooling directly inside the chip is a promising approach for more efficient thermal management<a href="/articles/s41586-020-2666-1#ref-CR5">5</a>,<a href="/articles/s41586-020-2666-1#ref-CR10">10</a>,<a href="/articles/s41586-020-2666-1#ref-CR11">11</a>. However, even in state-of-the-art approaches, the electronics and cooling are treated separately, leaving the full energy-saving potential of embedded cooling untapped. Here we show that by co-designing microfluidics and electronics within the same semiconductor substrate we can produce a monolithically integrated manifold microchannel cooling structure with efficiency beyond what is currently available. Our results show that heat fluxes exceeding 1.7 kilowatts per square centimetre can be extracted using only 0.57 watts per square centimetre of pumping power. We observed an unprecedented coefficient of performance (exceeding 10,000) for single-phase water-cooling of heat fluxes exceeding 1 kilowatt per square centimetre, corresponding to a 50-fold increase compared to straight microchannels, as well as a very high average Nusselt number of 16. The proposed cooling technology should enable further miniaturization of electronics, potentially extending Moore's law and greatly reducing the energy consumption in cooling of electronics. Furthermore, by removing the need for large external heat sinks, this approach should enable the realization of very compact power converters integrated on a single chip.

Embedded Cooling Method with Monolithic Dual-Layer Microchannel Cold Plate for High-Power Chips

Micro-dielectric-droplet impingement cooling system based on MEMS

Advancing Cryogenic Electronic Cooling: A Case Study on Embedded Manifold Microchannels in Micromachined Joule-Thomson Coolers

Embedded microfluidic cooling with compact double H type manifold microchannels for large-area high-power chips

Embedded Cooling with 3D Manifold for High Power Application to 3020W Power

A Miniaturized Integrated System for Embedded Microchannel Cooling with Manifolds

An Experimental Study of Microchannel and Micro-Pin-Fin Based On-Chip Cooling Systems with Silicon-to-Silicon Direct Bonding.

Numerical Study on Hybrid Discontinuous Microchannel Heat Sink Combining Manifold with Pin Fins (DMC-MPF) for High Power Electronic Device

Embedded Micro-Pin Fin Heat Sink of Two-Phase Liquid Cooling for High Heat Flux 3D ICs

Two-Phase Liquid Cooling for High-Power Microelectronics via Embedded Micro-Pin Fin Heat Sink

A Comparative Numerical Analysis of Cold Plates for Thermal Management of Chips With Hotspots

Design, integration and performance analysis of a lid-integral microchannel cooling module for high-power chip

Jet Microchannel with Sawtooth Wall for Efficient Cooling of High-Power Electronics

Case-embedded cooling for high heat flux microwave multi-chip array

Electrically driven chip cooling device using hybrid coolants of liquid metal and aqueous solution

Experimental study on single-phase hybrid microchannel cooling using HFE-7100 for liquid-cooled chips

Investigation of Z-type Manifold Microchannel Cooling for Ultra-High Heat Flux Dissipation in Power Electronic Devices

Optimization of Embedded Cooling for Hotspots Based on Compound Plate Thermal Spreading Model

Embedded Cooling for High-heat-flux Hotspots with Different Sizes

Co-designing electronics with microfluidics for more sustainable cooling

Heat Dissipation Characteristics of a Jetting Staggered Microchannel for Cooling a Large-area High-performance SOC Chip