Abstract:It is highly desired to efficiently dissipate the high heat flux generated in electronics. A novel hybrid microchannel heat sink combining manifold with secondary oblique channels (MMC-SOC) has been proposed and studied numerically in our previous work. The current study conducts the fabrication and experimental test of the hybrid microchannel heat sink using dielectric fluid HFE-7100. The volume flow rate qv ranges from 211 to 580 mL/min, with channel Reynolds numbers between 278 and 905 for heat fluxes q'' = 20, 25, 30 and 35 W/cm2. The results indicate that the MMC-SOC heat sink can simultaneously reduce the thermal resistance Rt and pressure drop ∆P. For heat sinks with channel height Hc = 60 μm, an 11% reduction in ∆P and a 24% reduction in Rt are obtained compared to conventional manifold microchannel (MMC) heat sink for qv = 580 mL/min and q'' = 20 W/cm2. As qv increases, the ratio (Rt/Rt0) becomes smaller and (∆P/∆P0) becomes larger, which indicates an enhanced ability of reducing Rt and a suppressed ability of reducing ∆P. For the maximum qv = 580 mL/min and q'' = 35 W/cm2, the MMC-SOC heat sink can maintain a maximum chip temperature of 53 °C with a pressure drop of only 3.77 kPa. Moreover, the proposed MMC-SOC heat sink has a lower pressure drop compared to MMC heat sink owing to a reasonable design, even though the Reynolds number of the MMC-SOC heat sink reaches up to 883. This provides a very promising scheme for safe and efficient single-phase microchannel cooling used in the thermal management of electronics with high heat flux. In addition, the ratio (Rt/Rt0) will increase with increasing heat flux and increasing the flow rate becomes an effective way to further reduce the chip surface temperature at operating conditions with higher heat flux.

Embedded Cooling for High-heat-flux Hotspots with Different Sizes

Optimization of Embedded Cooling for Hotspots Based on Compound Plate Thermal Spreading Model

Embedded microfluidic cooling with compact double H type manifold microchannels for large-area high-power chips

Embedded Cooling with 3D Manifold for High Power Application to 3020W Power

Extremely high heat flux dissipation and hotspots removal with nature-inspired single-phase microchannel heat sink designs

Jet Microchannel with Sawtooth Wall for Efficient Cooling of High-Power Electronics

Case-embedded cooling for high heat flux microwave multi-chip array

Investigation of Z-type Manifold Microchannel Cooling for Ultra-High Heat Flux Dissipation in Power Electronic Devices

Embedded Cooling Method with Monolithic Dual-Layer Microchannel Cold Plate for High-Power Chips

Microfluidic Cooling for Distributed Hot-Spots

Efficient Thermal Management of High-Power Electronics Via Jet-Enhanced HU-type Manifold Microchannel

Numerical Study on Hybrid Discontinuous Microchannel Heat Sink Combining Manifold with Pin Fins (DMC-MPF) for High Power Electronic Device

A novel hybrid-composite microchannel heat sink for extreme hotspot mitigation

High performance heat sink with counter flow diverging microchannels

Toward extremely low thermal resistance with extremely low pumping power consumption for ultra-high heat flux removal on chip size scale

Microchannel heat sinks for hotspot thermal management: achieving minimal pressure drop and maximal thermal performance

Embedded Micro-Pin Fin Heat Sink of Two-Phase Liquid Cooling for High Heat Flux 3D ICs

Heat Dissipation Characteristics of a Jetting Staggered Microchannel for Cooling a Large-area High-performance SOC Chip

Experimental study on single-phase hybrid microchannel cooling using HFE-7100 for liquid-cooled chips

Investigation of an Embedded Cooling RF Silicon Interposer for an Ultrahigh Heat Flux GaN TR Array

Microscale Heat Transfer Enhancement Using Thermal Boundary Layer Redeveloping Concept