Abstract:The proposed radio‐frequency receiver is a low‐IF receiver architecture, not a zero‐IF Rx, with the IF frequency being twice the channel bandwidth, that is, the intermediate frequency in the RF receiver equals 200 MHz. The radio‐frequency receiver consists of a low‐noise driver stage (RF stage) and an in‐phase/quadrature of phase (I/Q) demodulator. The low‐noise driver stage is designed using a complementary current‐reuse common‐gate configuration with shunt feedback to achieve wideband RF input matching with ultra‐low power dissipation, enhancing linearity compared to the conventional configuration. Summary This paper presents a battery‐free ultra‐low‐power (ULP), highly integrated, and wide‐bandwidth low‐IF radio‐frequency (RF) receiver designed for millimeter‐wave (mm‐Wave) applications, utilizing 130‐nm CMOS technology. The suggested RF receiver is suitable for K‐band (n258) at 26 GHz, Ka‐band (n261 and n257) at 28 GHz, and the LMDS band at 28 GHz in fifth‐generation applications. The proposed radio receiver consists of a low‐noise driver stage implemented using a complementary current‐reuse common gate with an active shunt feedback configuration and an in‐phase/quadrature‐phase (I/Q) demodulator. The proposed RF receiver employs transformer coupling to isolate the DC path between the transconductance stage (RF stage) and the switching stage (IF stage). The driver stage expands the RF input impedance while maintaining acceptable linearity and gain with ultra‐low DC power dissipation. The DC supplies for the proposed mm‐Wave RF receiver are generated using two novel energy‐harvesting voltage doubler circuits to provide positive and negative voltages. The proposed mm‐Wave radio receiver consumes 0.475 mW from a 1.1 V DC supply and exhibits a power conversion gain (CG) of 6.3 dB, with a 3 dB frequency bandwidth extending from 22 to 32 GHz. The input 1‐dB compression point (P1dB) of the RF receiver is −2.65 dBm, and the input third‐order intercept point (IIP3) is 7.35 dBm. With a sensitivity of −66.5 dBm at a 100 MHz channel bandwidth and a dynamic range of 63.85 dB, the suggested receiver demonstrates notable performance characteristics. The proposed radio receiver boasts an excellent figure of merit (FoM) at 215 dB, surpassing published works by a margin of 8–31 dB. The primary positive supply voltage is derived from a double‐band positive voltage doubler with series resonance feedback and parallel resonance networks, efficiently achieving the desired DC voltage and output current (1.1 V and 450 μA). Meanwhile, the negative gate bias is provided by a negative voltage doubler, ensuring the necessary negative voltage (−0.5 V) without any current conditions.

0.6‐V 2.1‐mw RF Receiver Based on Passive Mixing and Master–slave Common‐mode Rejection Technique in 65 Nm CMOS

A 0.6-V Zero-IF/Low-IF Receiver with Integrated Fractional-N Synthesizer for 2.4-Ghz ISM-Band Applications.

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

A 0.6V 32.5mw Highly Integrated Receiver for 2.4ghz ISM-Band Applications

A 0.1-1.9Ghz 65nm CMOS Variable-Gain Mixer-First Receiver with DSA and Noise-Shaping TIA.

Design of a Low Power 60ghz OOK Receiver in 65nm CMOS Technology

A 0.6v Passive Mixer with High Conversion Gain in 65 Nm Cmos Process

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

20 . 6 A 0 . 6 V 32 . 5 mW Highly Integrated Receiver for 2 . 4 GHz ISM-Band Applications

Design of Ultra-Low-Power 60-Ghz Direct-Conversion Receivers in 65-Nm CMOS

A CMOS MedRadio Receiver RF Front-End with a Complementary Current-Reuse LNA

An 89 Μw MICS/ISM Band Receiver for Ultra-Low-power Applications.

A 0.8V, 152 μ W, 433 MHz Mixer-First Receiver with a Self-Adjusted Frequency Tracking Loop

A Reconfigurable Passive Mixer for Multimode Multistandard Receivers in 0.18 Μm CMOS

A 1.2V 0.1&#x2013;3ghz Software-Defined Radio Receiver Front-End in 130nm CMOS

A Reconfigurable 0.7–2.6ghz Wideband Mixer for Multi-Mode Multi-Standard Receivers in 0.18μm RF CMOS

A Differential Low-Voltage High Gain Current-Mode Integrated RF Receiver Front-End

An 8mw Ultra Low Power 60ghz Direct-Conversion Receiver with 55db Gain and 4.9db Noise Figure in 65nm CMOS

A Low-Power 2.4-GHz Receiver Front End With a Lateral Current-Reusing Technique

A Low-Noise W-Band Receiver in a 28-nm CMOS Technology

Battery‐free ultra‐low‐power radio‐frequency receiver for mm‐wave applications using 130‐nm CMOS technology with harvested DC supplies