Abstract:In this paper, a method of stamping first and then strong staggered spinning was studied to process Cu/Al laminated composite into thin-walled composite tube. The multi-scale interfacial structure, element diffusion, microscopic evolution, mechanical properties and fracture mechanism of the tubes with different thickness reduction (TR) were studied by different material characterization methods. The results show that with the increase of TR, the interface experienced brittle layer fracture, fresh metal extrusion, new diffusion layer and the formation of the interface, and always maintained a good combination. Under the shearing force of the outer rotating wheel, the grain sizes of both sides of Cu and Al with 80%TR are reduced to 0.75 μm and 1.15 μm by 82% and 80% refinement, respectively. The deformation of Cu is induced by work hardening and dynamic recrystallization (DRX), and the strain inhomogeneity caused by 〈111〉 fiber is transferred from grain boundary to interior with the increase of TR. The Al side is mainly dominated by dynamic recovery (DRV), and the grain presents random and uneven strain, and finally changes to the internal grain strain mutation dominated by 〈001〉 fiber. The Cu grains near the rotating wheel are elongated at an inclination of 45°, but others at the interface are fine and equiaxed, suggesting good deformation coordination at the interface. The deformation coordination and strain transfer are stimulated by the change of micro-nano mechanical properties of Cu, interface and Al. Compared with the initial state (IS), the YS (124.52 MPa) and UTS (145.26 MPa) of Cu/Al composite tube with 80%TR are improved by 58% and 10%, respectively. Cu and Al show ductile fracture and brittle fracture respectively, and more metastable critical cracks are excited at the interface to avoid debonding and delamination.

Effect of a Thin Cr Layer on the Microstructures and Fracture Behaviours of Copper Films

Effects of Cr addition on the microstructural, mechanical and electrical characteristics of Cu–6wt.%Ag microcomposite

Inverse Effect of Thickness on the Ductility in Nanocrystalline Cu Films

Effect of Al2Cu constituent layer thickness discrepancy on the tensile mechanical behavior of Cu/Al2Cu/Al layered composites: A molecular dynamics simulation

Combined effects of residual stress and microstructure on degradation of Cu thin films on Si

EFFECT OF HEAVILY DRAWING ON THE MICROSTRUCTURE AND PROPERTIES OF Cu-Cr ALLOYS

Deformation and Fracture Behavior of Electrocodeposited Alumina Nanoparticle/Copper Composite Films

Fracture in A Thin Film of Nanotwinned Copper

Research on Deforming Mechanism of Nanocrystalline Cu Thin Film under Contact Deformation

Morphology and microstructure control of sputter-deposited copper films by addition of Cr

Effect of Multi-Interfacial Structure on Fracture Resistance of Composite TiSiN/Ag/TiSiN Multilayer Coating

Effect of Cr micro-alloying on microstructure and mechanical properties of alumina whisker and graphene co-reinforced copper matrix composites

Micro-nano interface structure and mechanical characteristics of thin wall Cu/Al composite tubes prepared by strong staggered spinning

Microstructure evolution and anti-wear mechanism of Cu film fabricated by magnetron sputtering deposition

Copper effects on the microstructures and deformation mechanisms of CoCrFeNi high entropy alloys

Molecular dynamics studies of the effect of intermediate Fe layer thickness on the enhanced strength and ductility of Cu/Fe/Ni multilayer

Microstructure and mechanical behavior of Ti/Cu/Ti laminated composites produced by corrugated and flat rolling

Modulating Individual Thickness for Optimized Combination of Strength and Ductility in Cu/Ru Multilayer Films

Effect of Alloying on Dislocation Structure, Cracking and Fracture of Cu–Al and Cu–Mn Alloys in Low-Stability States

Texture characteristics and tensile deformation behavior of Cu/Al layered composites prepared by cast-rolling method

Study on strengthening and toughening mechanisms of cu/Al composites dominated by interface layer