Abstract:The purpose of this paper is to examine the microstructural evolution and mechanical properties of Ni/Ti laminated composite produced by a cross-accumulative roll bonding (CARB) method. The SEM images showed that no void and delamination were observed which indicates that the layers were strongly bonded together. In addition to the thickness reduction and increased number of interfaces, plastic instabilities took place with an increase in CARB passes; the wavy-like interfaces appeared as a result of the necking and shear bands formation. However, due to the effect of uniform rolling pressure and rotation of rolling direction during the CARB process, all layers remained continuous in all CARB passes. The most marked observation coming from EBSD analyses was the formation of fine grains surrounded by a high fraction of high-angle grain boundaries (HAGBs). Based on the microtexture analyses on Ti and Ni layers, it was found that by increasing the rolling passes, a crystallographic texture formed in Ti layers gradually changes from the basic {0001}<112 ̅0 > system into the system dominated by {0001}<101 ̅0 > prismatic-like orientations. In the case of the crystallographic texture formed in Ni layers, there was a significant increase in the intensity of the Q{013}<231>; P{011}<122 > and Goss {011}<100>, indicating the formation of shear strain-assisted type of texture. Furthermore, with an increase in the CARB passes, the mechanical properties improved due to strong interfaces and grain refinement. The maximum values of the yield strength, tensile strength, and elongation reached 842 MPa, 936 MPa, and 7.1% respectively, in the final CARB pass. In addition, ductile fracture mainly occurred on fracture surfaces of Ti and Ni layers even though by increasing passes, cleavage facets appeared due to strain hardening.Graphic Abstract

Microstructure and mechanical behavior of Ti/Cu/Ti laminated composites produced by corrugated and flat rolling

Texture characteristics and tensile deformation behavior of Cu/Al layered composites prepared by cast-rolling method

Fracture toughness, wear, and microstructure properties of aluminum/titanium/steel multi-laminated composites produced by cross-accumulative roll-bonding process

Microstructure and mechanical properties of Ti6Al4V based laminated composites at various rolling reductions

Formation mechanism of dynamic multi-neutral points and cross shear zones in corrugated rolling of Cu/Al laminated composite

Layer structure-based grain refinement mechanism and its effect on the mechanical behavior of Ti/Al laminated metal composites

On Evolution of Grain Refinement and Mechanical Properties in Cu/Low-Carbon Steel/Cu Composites Manufactured by Different Rolling Routes

Microstructure and Properties of Cold Rolled Cu70Cr30 Composite

Microstructure and Mechanical Properties of AA1050/AA6061 Laminated Composites Fabricated through Three-Cycle Accumulative Roll Bonding and Subsequent Cryorolling

Microstructure, Texture and Tensile Properties of Nickel/Titanium Laminated Composites Produced by Cross Accumulative Roll Bonding Process

Study on microstructure evolution and fracture behavior of Al/Al/Cu multilayer composites

Effects of Direct Rolling Deformation on the Microstructure and Tensile Properties of the 2.5 Vol% (tibw+ticp)/ti Composites

Fracture behaviors and microstructural failure mechanisms of laminated Ti–TiBw/Ti composites

Comparison of Rolling and Transverse Direction Properties of Al/Ti Laminated Metal Composites Prepared by Cold Roll Bonding and Subsequent Annealing

Microstructure Evolution and Bending Fracture Mechanism of As-Rolled Gradient-Laminated Network Titanium Matrix Composites

Effect of Cyclic Warm-Rolling Technique on Mechanical Properties of MoCu30 Thin Plates with Heterogeneous Structure

Interface characteristics and mechanical behavior of Cu/Al clad plate produced by the corrugated rolling technique

Microstructure evolution, mechanical properties and tailoring of coefficient of thermal expansion for Cu/Mo/Cu clad sheets fabricated by hot rolling

Fracture Mechanism of a High Tensile Strength and Fracture Toughness Ti6Al4V–TiAl Laminated Composite

Interface Characteristics and Mechanical Properties of a Ti–TiAl Laminated Composite

Study of microstructure and mechanical properties of quasi-continuous network structured (Ti3AlC2-Al3Ti)/2024Al composites based on hot rolling