Abstract:Three-layered Ti/Cu/Ti clad materials fabricated by cold roll-bonding process and in the following underwent heat treatment cycles. Microstructure evolution and mechanical properties of as-rolled and annealed samples studied by SEM, XRD, microhardness and tensile examinations. According to the results, as-rolled and treated samples contained several IMCs at their Ti/Cu interfaces while thickness of the reaction layer enhanced noticeably by annealing. Examined average IMC layers' thickness were 1.34, 1.61, 2.39 and 5.39 μm, for as-rolled, 300, 500 and 700 °C annealed specimens, respectively, consisting four different phases of CuTi2, CuTi, Cu3Ti2, and Cu4Ti. However, continuity, uniformity and thickness variation as well as the growth rate during treating for each layer was distinct. From SEM and XRD results that acquired from separated surfaces, major debonding occurred at CuTi2/CuTi and CuTi/Cu3Ti2 interfaces suggesting that bonding strength for these IMC layers were weaker than those for the other IMC/IMC interfaces and the parent-metal/IMCs. The stress-strain curves demonstrated that the strength decreased and subsequently ductility improved by annealing up to 700 °C. Meanwhile, SEM analyses revealed that cracks within IMC layers during tensile deformation emerged only in specimen annealed at 700 °C; however, it did not lead debonding or layer separation similar to other clad metals reported in literature. By fractography, it is indicated that dimples formed in the whole fracture surface of as-rolled and annealed specimens at 300 and 500 °C. For the 700 °C annealed specimen, however fracture mode was ductile, dimples hardly noticed since the cracks propagation and extension path was along the weak IMC interfaces. In addition, this sample unlike others exhibited limited necking extension before failure. According to the obtained results and as the current research's novelty, it is claimable that intermetallics formed in Ti/Cu clad materials would be more ductile comparing with other compounds reported for talented cladding metals in literature.

Effect of intermetallic compounds (IMCs) on the interfacial bonding strength and mechanical properties of pre-rolling diffusion ARBed Al/Ti laminated composites

Microstructure Evolution During Roll Bonding and Growth of Interfacial Intermetallic Compounds in Al/Ti/Al Laminated Metal Composites

Formation and effect of intermetallic compounds in the interface of copper/aluminum composites under rolling conditions

Effect of Zn and Ti Transition Foil on the Microstructure and Mechanical Properties of Hot Rolling Bonded Al/Mg Composite Plates

Layer structure-based grain refinement mechanism and its effect on the mechanical behavior of Ti/Al laminated metal composites

Effect of Annealing Parameters on the Interfacial Structures and Mechanical Properties of Al/Mg/Al Laminates with Large Thickness Ratio

Microstructure Evolution and Mechanical Properties of Al/Mg-Li/Al Laminate Metallic Composites Via Hot Roll Bonding and Subsequent Cryorolling

Effect of Wavy Profile on the Fabrication and Mechanical Properties of Al/Ti/Al Composites Prepared by Rolling Bonding: Experiments and Finite Element Simulations

Interface evolution and strengthening of two-step roll bonded cu/Al clad composites

Comparison of Rolling and Transverse Direction Properties of Al/Ti Laminated Metal Composites Prepared by Cold Roll Bonding and Subsequent Annealing

Interfacial fracture characteristics of Mg/Al composite plates with different thickness ratios by asymmetrical rolling with differential temperature rolls

Effect of Rolling Parameters on Microstructure, Texture, and Mechanical Properties of Al/Mg/Al Laminated Composites

Effect of Intermetallic Compounds on the Mechanical Properties of Cu/Al Clad Sheets with an SS304 Interlayer

Roll bonding characteristics of the Mg/Zn/Cu/Al multilayered composite produced by the ARB process

Interfacial microstructure evolution,growth kinetics and mechanical properties of Fe/Al dissimilar metal j oints

Effects of recrystallization and element diffusion behavior on interfacial bonding quality and mechanical properties of aluminum laminated composites

Effect of Annealing and Cold Rolling on Interface Microstructure and Properties of Ti/Al/Cu Clad Sheet Fabricated by Horizontal Twin-Roll Casting

Micromechanical behavior of multilayered Ti/Nb composites processed by accumulative roll bonding: An in-situ synchrotron X-ray diffraction investigation

High Strength and Thermal Stability of Multilayered Cu/Al Composites Fabricated Through Accumulative Roll Bonding and Cryorolling

Effects of asymmetry and annealing on interfacial microstructure and mechanical properties of Cu/Al laminated composite fabricated by asymmetrical roll bonding

Effect of interfacial intermetallic compounds evolution on the mechanical response and fracture of layered Ti/Cu/Ti clad materials