Abstract:Publication date: 30 May 2022 Source: Key Engineering Materials Vol. 921 Author(s): Hong Qing Lv, Ze Yuan Fan, Xing Xu, Xin Huang The finite element software abaqus is used to establish the model of split-sleeve cold extrusion (elastic-plastic) of the 7050 aluminum alloy test plate with hole and the reaming model after cold extrusion, and the processes are simulated. In these processes, the simulation results of cold extrusion are compared with the measured results, the law of residual stress distribution after cold extrusion is explored, and the influence of the amount of reaming on the distribution of residual stress during the reaming process is discussed. The simulation results show a good agreement with the experimental data; the residual compressive stress after cold extrusion increases first and then decreases from the intrusion end to the extrusion end. Specifically, the maximum value is near the middle surface, and the value of the second half is larger than that of the first half; after the cold extrusion with the split sleeve, a "ridge" appears, leading to uneven distribution of the residual stress and extrusion amount along the circumference of the hole. Moreover, the minimum value of the tangential residual stress lies on the intrusion surface, vertical to the "ridge". After reaming, new residual compressive stress will be introduced, which will increase the residual compressive stress on the intrusion surface. In this sense, proper reaming can increase the residual compressive stress and its peak value, resulting in a fatigue gain.

Simulation of Compound Cold Extrusion Al-Zn-Mg-Cu Alumium Alloys

Simulation and Experiment Analysis of Dual-directional Extrusion of AZ31 Mg Alloy

Investigation of Microstructures and Mechanical Properties of Ultra-High Strength Al-Zn-Mg-Cu Alloy Prepared by Rapid Solidification and Hot Extrusion

Simulation Research on Cold Extrusion Strengthening and Reaming of 7050 Aluminum Alloy Plate Hole

Numerical and Experimental Investigation on Hot Backward Extrusion Process of Mg-Gd-Y-Zn-Zr Magnesium Alloy

Microstructures and Mechanical Properties of Hot-extruded Mg-6Zn-xCu-0.6Zr(x=0,0.5,1.0,1.5) Alloys

Simulation of Extrusion Process of AZ31 Magnesium Alloy

Deformation Characteristics and Microstructure Analysis of Aluminum Alloy Component with Complex Shape by Cold Orbital Forming

Ultra-high strength Al-Zn-Mg-Cu alloys with high zinc content prepared via powder hot extrusion

SIMULATION OF ALUMINUM FIXTURE PART HOT EXTRUSION PROCESS WITH THE FINITE VOLUME METHOD

Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy

Isothermal Deformation of Spray Formed Al–Zn–Mg–Cu Alloy

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

FEM and FVM Compound Numerical Simulation of Aluminum Extrusion Processes

Hot Deformation Behavior and Processing Maps of an As-Cast Al-5Mg-3Zn-1Cu (wt%) Alloy

Achieving high strain rate superplasticity in an Al-Cu-Li alloy processed by thermo-mechanical processing

Evolution of Microstructure and Mechanical Properties of Al-Zn-Mg-Cu Alloy by Extrusion and Heat Treatment

Super High Strength Aluminum Alloy Processed By Mechanical Alloying And Hot Extrusion

Effect of multi-stage solution and aging process on microstructure and properties of Al–10.7Zn–2.8Mg–1.2Cu–0.2Zr aluminum alloy extrusion materials

Simulation Analysis on Micro Hole Forming of Aluminum Alloy in Extrusion Casting Process