Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. A multi-grain conical grinding head capable of performing both peripheral and end-face grinding was created in Abaqus to simulate conventional grinding (CG) and axial ultrasonic-assisted vibration grinding (AUVAG) on Ti-6Al-4V alloy. A comparative analysis was conducted to examine the effects of key grinding parameters on the fluctuation amplitude and mean value of grinding forces in CG and AUVAG. The mechanism of ultrasonic vibration's influence on grinding forces was analyzed, and a theoretical model for normal and tangential grinding forces in peripheral grinding of Ti-6Al-4V was established. Additionally, the surface morphology of CG and AUVAG was analyzed. The study found that the fluctuation amplitude of grinding forces in both AUVAG and CG increases with the axial grinding depth, feed rate, ultrasonic amplitude, and ultrasonic frequency, while it decreases with increasing spindle speed. However, the fluctuation amplitude in AUVAG is greater than that in CG. The average grinding forces in both CG and AUVAG increase with the grinding depth and feed rate, and decrease with the spindle speed. Compared to CG, the mean Fx ([math]) and Fy ([math]) are lower in AUVAG, while the mean Fz ([math]) is higher. Under different axial grinding depths, the maximum reduction in [math] and [math] for AUVAG is 4.70% and 5.18%, respectively, while the maximum increase in [math] is 77.48%. At different feed rates, the maximum reduction in [math] and [math] for AUVAG is 3.02% and 21.01%, respectively, while the maximum increase in [math] is 81.67%. Under different spindle speeds, the maximum reduction in [math] and [math] is 7.20% and 17.82%, respectively, and the maximum increase in [math] is 281%. As the ultrasonic amplitude and frequency increase, [math] significantly rises, but the effect on [math] and [math] is weak. AUVAG improves the surface quality of the specimen.

Study on Effects of Ultrasonic Vibration on Grinding Force

Study on Grinding Force Model in Ultrasonic Vibration Assisted Grinding for Ductile Materials

Study on the system matching of ultrasonic vibration assisted grinding for hard and brittle materials processing

Research on the System Matching Model in Ultrasonic Vibration-Assisted Grinding

Experimental Studies on Grinding Forces and Force Ratio of the Unsteady-State Grinding Technique

An experimental investigation of system matching in ultrasonic vibration assisted grinding for titanium

Research on the effect of grinding force on the axial ultrasonic vibration-assisted grinding of Ti-6Al-4V with multi-grain conical grinding head

Experimental Research on the Effect of Grinding Parameters on Ceramic Machined Surface Roughness

Effects of Horizontal Vibration Assistance on Surface Roughness in Magnetic Abrasive Finishing

Grinding force assessment in tangential ultrasonic vibration-assisted grinding gear: Analytical model and experimental verification

Establishment of dynamic grinding force model for ultrasonic-assisted single abrasive high-speed grinding

Study on force reduction mechanism in ultrasonic-assisted grinding based on single-grain scratching

Analytical modeling of abrasive grain-workpiece cutting coefficient and experimental investigation on tangential ultrasonic vibration-assisted forming grinding gear

Study on Grinding Force of Two-Dimensional Ultrasonic Vibration Grinding 2.5D-C/SiC Composite Material

An Improved Cutting Force Model for Ultrasonically Assisted Grinding of Hard and Brittle Materials

Grinding force model for ultrasonic assisted grinding of γ-TiAl intermetallic compounds and experimental validation

Grinding force modeling in ultrasonic-assisted face grinding of ZrO2 ceramics and influence of grinding wheel wear on its accuracy

Modeling of Grinding Force in Constant-Depth-Of-Cut Ultrasonically Assisted Grinding

Experimental Investigation on the Combined Effects of Mechano-Chemical and Ultrasonic Vibration in Titanium Alloy Grinding

Mechanism study on ultrasonic vibration assisted face grinding of Hard and brittle materials

Intermittent cutting behavior and grinding force model in ultrasonic vibration-assisted grinding K4002 nickel-based superalloy