Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. A multi-grain conical grinding head capable of performing both peripheral and end-face grinding was created in Abaqus to simulate conventional grinding (CG) and axial ultrasonic-assisted vibration grinding (AUVAG) on Ti-6Al-4V alloy. A comparative analysis was conducted to examine the effects of key grinding parameters on the fluctuation amplitude and mean value of grinding forces in CG and AUVAG. The mechanism of ultrasonic vibration's influence on grinding forces was analyzed, and a theoretical model for normal and tangential grinding forces in peripheral grinding of Ti-6Al-4V was established. Additionally, the surface morphology of CG and AUVAG was analyzed. The study found that the fluctuation amplitude of grinding forces in both AUVAG and CG increases with the axial grinding depth, feed rate, ultrasonic amplitude, and ultrasonic frequency, while it decreases with increasing spindle speed. However, the fluctuation amplitude in AUVAG is greater than that in CG. The average grinding forces in both CG and AUVAG increase with the grinding depth and feed rate, and decrease with the spindle speed. Compared to CG, the mean Fx ([math]) and Fy ([math]) are lower in AUVAG, while the mean Fz ([math]) is higher. Under different axial grinding depths, the maximum reduction in [math] and [math] for AUVAG is 4.70% and 5.18%, respectively, while the maximum increase in [math] is 77.48%. At different feed rates, the maximum reduction in [math] and [math] for AUVAG is 3.02% and 21.01%, respectively, while the maximum increase in [math] is 81.67%. Under different spindle speeds, the maximum reduction in [math] and [math] is 7.20% and 17.82%, respectively, and the maximum increase in [math] is 281%. As the ultrasonic amplitude and frequency increase, [math] significantly rises, but the effect on [math] and [math] is weak. AUVAG improves the surface quality of the specimen.

Grinding force assessment in tangential ultrasonic vibration-assisted grinding gear: Analytical model and experimental verification

Study on Grinding Force Model in Ultrasonic Vibration Assisted Grinding for Ductile Materials

Study on the system matching of ultrasonic vibration assisted grinding for hard and brittle materials processing

Analytical modeling of abrasive grain-workpiece cutting coefficient and experimental investigation on tangential ultrasonic vibration-assisted forming grinding gear

Research on the System Matching Model in Ultrasonic Vibration-Assisted Grinding

Prediction and Verification Analysis of Grinding Force in the Single Grain Grinding Process of Fused Silica Glass

Grinding force model for ultrasonic assisted grinding of γ-TiAl intermetallic compounds and experimental validation

Force modeling of vertical surface grinding considering wheel-workpiece contact geometry

Establishment of dynamic grinding force model for ultrasonic-assisted single abrasive high-speed grinding

Generation Mechanism Modeling of Surface Topography in Tangential Ultrasonic Vibration-Assisted Grinding with Green Silicon Carbide Abrasive Wheel

Tangential Ultrasonic-Vibration Assisted Forming Grinding Gear: An Experimental Study

Research on the effect of grinding force on the axial ultrasonic vibration-assisted grinding of Ti-6Al-4V with multi-grain conical grinding head

Modeling of Grinding Force in Constant-Depth-Of-Cut Ultrasonically Assisted Grinding

Modeling and Simulation of Grinding Surface Topography Considering Wheel Vibration

Intermittent cutting behavior and grinding force model in ultrasonic vibration-assisted grinding K4002 nickel-based superalloy

A grinding force model in two-dimensional ultrasonic-assisted grinding of silicon carbide

AAC theory for ultrasonic vibration-assisted grinding

Grinding force modeling in ultrasonic-assisted face grinding of ZrO2 ceramics and influence of grinding wheel wear on its accuracy

Numerical modeling of material removal mechanism and surface topography for gear profile grinding

Thermal Analysis of Ultrasonic Vibration-Assisted Grinding with Moment-Triangle Heat Sources

An Improved Cutting Force Model for Ultrasonically Assisted Grinding of Hard and Brittle Materials