Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. A multi-grain conical grinding head capable of performing both peripheral and end-face grinding was created in Abaqus to simulate conventional grinding (CG) and axial ultrasonic-assisted vibration grinding (AUVAG) on Ti-6Al-4V alloy. A comparative analysis was conducted to examine the effects of key grinding parameters on the fluctuation amplitude and mean value of grinding forces in CG and AUVAG. The mechanism of ultrasonic vibration's influence on grinding forces was analyzed, and a theoretical model for normal and tangential grinding forces in peripheral grinding of Ti-6Al-4V was established. Additionally, the surface morphology of CG and AUVAG was analyzed. The study found that the fluctuation amplitude of grinding forces in both AUVAG and CG increases with the axial grinding depth, feed rate, ultrasonic amplitude, and ultrasonic frequency, while it decreases with increasing spindle speed. However, the fluctuation amplitude in AUVAG is greater than that in CG. The average grinding forces in both CG and AUVAG increase with the grinding depth and feed rate, and decrease with the spindle speed. Compared to CG, the mean Fx ([math]) and Fy ([math]) are lower in AUVAG, while the mean Fz ([math]) is higher. Under different axial grinding depths, the maximum reduction in [math] and [math] for AUVAG is 4.70% and 5.18%, respectively, while the maximum increase in [math] is 77.48%. At different feed rates, the maximum reduction in [math] and [math] for AUVAG is 3.02% and 21.01%, respectively, while the maximum increase in [math] is 81.67%. Under different spindle speeds, the maximum reduction in [math] and [math] is 7.20% and 17.82%, respectively, and the maximum increase in [math] is 281%. As the ultrasonic amplitude and frequency increase, [math] significantly rises, but the effect on [math] and [math] is weak. AUVAG improves the surface quality of the specimen.

Research on the effect of grinding force on the axial ultrasonic vibration-assisted grinding of Ti-6Al-4V with multi-grain conical grinding head

Study on Grinding Force Model in Ultrasonic Vibration Assisted Grinding for Ductile Materials

An experimental investigation of system matching in ultrasonic vibration assisted grinding for titanium

Effect of Ultrasonic Vibration Assisted Grinding Process on Surface Topography and Properties of C/SiC Composite

An Experimental Investigation on Ultrasonic Vibration-Assisted Grinding of Sio2f/Sio2 Composites

Research on the System Matching Model in Ultrasonic Vibration-Assisted Grinding

Grinding force assessment in tangential ultrasonic vibration-assisted grinding gear: Analytical model and experimental verification

Grindability of γ-TiAl intermetallic compounds during ultrasonic vibration-assisted high efficiency deep grinding process

Development and performance of a novel ultrasonic vibration plate sonotrode for grinding

Study on grinding performance during ultrasonic vibration-assisted grinding ultra-high strength steels

Study on Effects of Ultrasonic Vibration on Grinding Force

Material removal mechanisms in ultrasonic vibration-assisted high-efficiency deep grinding γ-TiAl alloy

The material removal mechanism and surface characteristics of Ti-6Al-4 V alloy processed by longitudinal-torsional ultrasonic-assisted grinding

Analytical modeling of abrasive grain-workpiece cutting coefficient and experimental investigation on tangential ultrasonic vibration-assisted forming grinding gear

Establishment of dynamic grinding force model for ultrasonic-assisted single abrasive high-speed grinding

Grinding force model for ultrasonic assisted grinding of γ-TiAl intermetallic compounds and experimental validation

Intermittent cutting behavior and grinding force model in ultrasonic vibration-assisted grinding K4002 nickel-based superalloy

Thermal Analysis of Ultrasonic Vibration-Assisted Grinding with Moment-Triangle Heat Sources

Surface roughness model of ultrasonic vibration-assisted grinding GCr15SiMn bearing steel and surface topography evaluation

AAC theory for ultrasonic vibration-assisted grinding

Modeling of Grinding Force in Constant-Depth-Of-Cut Ultrasonically Assisted Grinding