Abstract:As a typical hexagonal close-packed structure metal, the dendritic morphology and preferential orientation of Mg would be influenced by many factors. Current investigations still fall short on the thorough description of the diversity and complexity of dendrites growth patterns and their origination, therefore, this paper reviewed recent research progress of this group on 3D characterization of microstructure in solidified magnesium alloys. Using synchrotron X-ray tomography and phase-field modeling, the formation mechanism of the diverse alpha-Mg (X) dendrites and the affections of alloying element (such as Al, Ca, Zn, and Sn), solute concentration on the growth selection and evolution of alpha-Mg dendrites during solidification were studied. The results indicate that the alloying elements and solute concentration would impose a significant influence on the morphology and orientation selection of the primary alpha-Mg dendrites. In Mg-Ca and Mg-Al (hcp-fcc) alloys, dendrites tend to grow with preferred orientation of <11<(2)over bar>0> or <22<(4)over bar>5> which is in good agreement with the traditional expected direction. The equiaxed growth dendrites in Mg-Sn (hcp-bct) alloys evolve as a structure with 18 branches, six of which grow on the basal plane along <11<(2)over bar>0> and the remaining 12 along <11<(2)over bar>X> (X approximate to 2) off the basal plane. For the case in Mg-Zn alloys, an orientation transition from <11<(2)over bar>0> on the basal plane to <11<(2)over bar>1> off the basal plane are observed with the increasing addition of Zn alloying element, a hyperbranched seaweed structure is also revealed with an interim composition. A probable explanation is that the addition of high anisotropy Zn would slightly alter the anisotropy of interfacial free energy in front of the growth interface which results in a dendrite orientation transition (DOT). These findings partially reveal the underlying formation mechanism and origination of the diversity dendritic morphologies and branching structures of alpha-Mg dendrites in Mg alloys. Furthermore, with the fast X-ray imaging facility, in situ observations of the 3D microstructure evolution in Mg alloys during solidification are also carried out and the evolution of alpha-Mg dendrites are obtained for further analysis.

The Effect of Low Cooling Rates on Dendrite Morphology During Directional Solidification in Mg–Gd Alloys: in Situ X-ray Radiographic Observation

Coupling in Situ Synchrotron X-ray Radiography and Phase-Field Simulation to Study the Effect of Low Cooling Rates on Dendrite Morphology During Directional Solidification in Mg–Gd Alloys

Effect of cooling rates on the dendritic morphology transition of Mg–6Gd alloy by in situ X-ray radiography

The effect of cross-section geometry of castings on dendrite evolution in Mg Gd alloys by in situ X-ray radiography

Observation of Dendrite Growth Velocity and Microstructure Transition in Highly Undercooled Single Phase Alloys

Influences of Solution Cooling Rate on Microstructural Evolution of a Multiphase Ni3Al-based Intermetallic Alloy

Dendritic Evolution During Coarsening of Mg-Zn Alloys Via 4D Synchrotron Tomography

Dynamic evolution of microstructure morphology in thin-sample solidification: Deep learning assisted synchrotron X-ray radiography

In Situ and Real-Time Observation of the Solidification Process of Al-20 Mass%Cu Alloy by Synchrotron X-Ray Radiography

Effect of Cooling Rate on the Solidified Microstructure of Mg-Gd-Y-Zr Alloy

Microstructure Evolution and Mechanical Properties of Directionally Solidified Mg-xGd (x=0.8, 1.5, and 2.5) Alloys

Microstructures and Growth Orientation of Directionally Solidification Mg-14.61Gd Alloy

Fast Synchrotron X-Ray Tomographic Quantification of Dendrite Evolution During the Solidification of Mg-Sn Alloys

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Influence of directional solidification variables on the microstructure and crystal orientation of AM3 under high thermal gradient

Synchrotron Tomographic Quantification of the Influence of Zn Concentration on Dendritic Growth in Mg-Zn Alloys

Characterization of Microstructures and Growth Orientation Deviating of Al2Cu Phase Dendrite at Different Directional Solidification Rates

In Situ Observation of Columnar-to-equiaxed Transition in Directional Solidification Using Synchrotron X-radiation Imaging Technique

RESEARCH PROGRESS ON 3D DENDRITE MORPHOLOGY AND ORIENTATION SELECTION DURING THE SOLIDIFICATION OF Mg ALLOYS: 3D EXPERIMENTAL CHARACTERIZATION AND PHASE FIELD MODELING

Microstructural Evolution with a Wide Range of Solidification Cooling Rates in a Ni-Based Superalloy

Effect of the Cooling Rate on the Microstructure of Directionally Solidified Casting (CMSX-4 Ni Superalloy)