Abstract:Stainless steels with excellent hardness and corrosion resistance performance have been widely used in industrial production. Ternary Fe-Cr-Ni alloys, as a model alloy of nickel chromium stainless steels, are of great importance in the fields of material science. Under non-equilibrium solidification condition, alloys may have new microstructure and improved performance. In this paper, two liquid ternary Fe-Cr-Ni alloys are deeply undercooled and rapidly solidified in a 3-m drop tube to investigate the microstructure evolution and solute distribution of alloy droplets with different sizes. In the drop tube experiments, the Fe-Cr-Ni alloy samples with a mass of 1.5 g are placed in a phi 16 mm x 150 mm quartz tube with a 0.5-mm-diameter orifice at its bottom and heated by induction heating device in a high vacuum chamber. Then the samples are melted and overheated to 200 K above their liquidus temperatures for several seconds. The alloy melt is ejected out of the small orifice and dispersed into numerous droplets after adding high pressure helium gas flow. The alloy droplets with diameters ranging from 68 mu m to 1124 mu m are achieved. After experiments, the alloy droplets with different sizes are mounted respectively. Then they are polished and etched. The drop tube technique provides an efficient way to study the rapid solidification mechanism of alloys. Besides the experiments, the dendrite growth velocities of primary phase in two Fe-Cr-Ni alloys are calculated theoretically using the modified LKT/BCT model. As droplet size decreases, both cooling rate and undercooling increase exponentially and the morphologies of two alloys become well refined. Under the near-equilibrium solidification condition with a cooling rate of 10 K/min, both alloys consist of coarse lath-like alpha phase. After rapid solidification of Fe81.4Cr13.9Ni4.7 alloy droplets during free fall, the microstructure presents a lath-like a phase, resulting from the solid-solid phase transition. As undercooling increases, the primary delta phase is converted from the coarse dendrite with long trunk into equiaxed grain. For Fe81.4Cr4.7Ni13.9 alloy, the microstructure is composed of alpha phase grains. The transition of primar gamma phase from coarse dendrite with long trunk to refined equiaxed grain occurs as the undercooling increases. Meanwhile, both dendrite trunk length and secondary dendrite arm spacing decrease drastically, suggesting that the rapid solidification is the main reason for grain refinement. Moreover, the relative segregation degree of solute Cr and Ni inside alpha phase grain also decreases obviously with the increase of undercooling, and the microsegregation of Ni is more remarkable than that of Cr. This suggests that the high cooling rate and undercooling cause the solute to be distributed evenly. Compared with that of gamma phase, the dendrite growth velocity of delta phase is large and its dendrite tip radius is small. The two phase transform from solute diffusion controlled growth into thermal diffusion controlled growth as undercooling increases to 8 K. When undercooling is larger than 8 K and within the experimental undercooling range, the dendrite growth of both Fe-Cr-Ni alloys is controlled by thermal diffusion.

Influences of Solution Cooling Rate on Microstructural Evolution of a Multiphase Ni3Al-based Intermetallic Alloy

Influence of Cooling Rate on the Formation of Bimodal Microstructures in Nickel-Base Superalloys During Continuous Two-Step Aging

Influence of Heating and Cooling Rate on Dissolution and Precipitation Behavior of Nickel-based Single Crystal Superalloy

Influence of Cooling Scenarios on the Evolution of Microstructures in Nickel-Based Single Crystal Superalloys

Influences Of The Heating And Cooling Rates On The Dissolution And Precipitation Behavior Of A Nickel-Based Single-Crystal Superalloy

Rapid dendrite growth mechanism and solute distribution in liquid ternary Fe-Cr-Ni alloys

Combined Effects of High Undercooling and Large Cooling Rate on the Microstructure Evolution and Hardening Mechanism of Rapidly Solidified Ti-Al Alloys

Effect of Annealing Treatment on Microstructure Evolution and Creep Behavior of a Multiphase Ni3Al-based Superalloy

The Temperature Influence on Early Precipitation Process of Ni-Al-Fe Alloy

Microscopic Phase-field Simulation of Effects of Re-ageing Temperature on Precipitation of Ni-Al-Cr Alloys

Solute Redistribution and Micromechanical Properties of Rapidly Solidified Multicomponent Ni-based Alloys

Precipitation of Intersected Plate-Like Γ′ Phase in Β and Its Effect on Creep Behavior of Multiphase Ni3Al-based Intermetallic Alloy

Dendrite Growth Kinetics and Microstructure Evolution Mechanism of Ni2tial Intermetallic Compound Within Substantially Undercooled Liquid Ni64al19ti17 Alloy

Influence of Cooling Strategy on Microstructure, Deformation Mechanism and Mechanical Properties of a Nickel-Based Superalloy

Microstructure Evolution of Primary Γ′ Phase in Ni3Al-Based Superalloy

Effect of Solution Cooling Rate on Microstructure Evolution and Mechanical Properties of Ni-based Superalloy ATI 718Plus

A Study of Solution Cooling Rate on Γ’ Precipitate and Hardness of a Polycrystalline Ni-based Superalloy Using a High-Throughput Methodology

The Effect of the Cooling Rates on the Microstructure and High-Temperature Mechanical Properties of a Nickel-Based Single Crystal Superalloy

Effect of Cooling Rate on Microstructure of Two Kinds of High Nb Containing Tial Alloys

Effect of Cooling Rate on Microstructure Evolution of Ti-45Al-8.5Nb-0.2W-0.2B-0.02Y Alloy During Multi-Step Heat Treatment

Dendrite evolution and quantitative characterization of γ′ precipitates in a powder metallurgy Ni-based superalloy by different cooling rates