Abstract:The micro-mechanical behavior of lamellar structured Ti6Al4V alloy was studied upon a small strain of 4.5 % compressional loading. The strain and stress concentration is found highly related to individual crystallographic orientation, their size, shape and grain-grain interaction, which usually concentrated along grain boundaries (GBs) typically soft and hard GBs owing to the strong strain gradient incurred. The generated local plastic deformation forms ledges through dislocation accumulation which further activate large amount of Geometrically necessary dislocations (GNDs) to accomodate strain incompatibility. Both strain and stress is maximized at some triple points (TPs). EBSD and crystal plasticity (CP) simulation disclosed some long range meso-bands (about 45° to loading direction) across multi-grains and mini-bands within grain interiors (GIs) with concentrated strain behavior which demonstrate slip and ductile behavior of the Ti6Al4V material. Prismatic slip is found dominated the slip behavior of the Ti6AL4V alloy (mostly from surface dislocation activation) which is away from some findings of literature and largely determined by its low critical resolved shear stress (CRSS). Dislocation is observed emitted from high angle grain boundaries (HAGBs) while slip transmission is observed through both low (LAGBs) and HAGBs. The substructures (α-lamellae), a type of LAGBs allocated within α-colonies, have no significant effect to dislocation movement. Fatigue failure can be inferred from the early stage of micro-mechanical behavior mainly judged by the amount of accumulated plastic deformation and induced stress/strain distribution amont the surroundings. Crack may nucleate from easy prismatic slip, local strain accumulation induced by soft and hard grain clustering (either hard embedded in soft or vice versa usually start from some TPs and sharp corners), or some concentrated long range slip activities. Other than the surface dents induced failure, shearing, cleavage, multi-cleavage and intergranular patterns is presumed highly related to the local microstructure, including their relative size, shape, orientation and grain-grain interactions. The multiple crack origins deemed for reduce fatigue life of shot peened samples regardless of the surface compressional residual stress being generated. The work helps understand the micro-mechanical deformation behavior (down to dislocation level) of Ti6Al4V alloy. Their fatigue and fracture can be inferred from such early stage of strain/stress behavior considering microstructural heterogeneities for similar alloys.

Investigation of Compressive and Damage Mechanisms in Fully Lamellar TiAl-Based Alloy

Study on the Influence of Compression Damage on Tensile Properties in Fully Lamellar Tial-Based Alloy

Effects of Tensile/compressive Overloads on Fatigue Crack Growth Behavior of an Extra-Low-interstitial Titanium Alloy

Study of tensile properties and fracture mechanisms of fully lamellar TiAl based alloy

DIC-based Studies of the Overloading Effects on the Fatigue Crack Propagation Behavior of Ti-6Al-4V ELI Alloy

Compressive performance and crack propagation in Al alloy/Ti2AlC composites

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Investigation on Fatigue Threshold Testing Methods in a Near Lamellar TiAl Alloy

Micro-mechanical behavior of lamellar structured Ti6Al4V alloy upon compression via experimental and crystal plasticity study

Dynamic Mechanical Properties of Ti–Al3Ti–Al Laminated Composites: Experimental and Numerical Investigation

Molecular Dynamics Simulation of Temperature and Ti Volume Fraction on Compressive Properties of Ti/Al Layered Composites

Effects of Al on crack propagation in titanium alloys and the governing toughening mechanism

Effect of residual stresses on the mechanical properties of Ti-TiAl laminate composites fabricated by hot-pack rolling

Stable strain hardening behavior of Ti-4Al-5Mo-5V-5Cr-1Nb alloy during plastic deformation

Meso-structure-Based Numerical Simulations of Deformation and Damage of Ti3AIC2/Al Composites by 3D Cylinder Model under Axial Compression

An investigation of ductile fracture behavior of Ti6Al4V alloy fabricated by selective laser melting

An Investigation of Small-crack and Long-crack Propagation Behavior in Titanium Alloy TC4 and Aluminum Alloy 7475-T7351

Microstructure and Mechanical Properties of Ti2AlC-reinforced TiAl Composites

In-Situ Observation of Fracture Behavior of Ti-Aluminide Multi-Layered Composites Produced by a Hybrid Sintering Process

Investigation on Compressive Behavior of Cu-35Ni-15Al Alloy at High Temperatures

Microstructure stability and damage mechanisms in an α/β Ti-6Al-4V-0.55Fe alloy during low cycle dwell-fatigue at room temperature