Abstract:Coal and biomass co-combustion in existing utility boilers is a promising option of mitigating the fossil energy crisis and reducing the gaseous emissions of NOx, SOx, and CO2. However, ash-related problems, including fouling, slagging, and corrosion cause damage to the heat exchange tube and reduce boiler efficiency. In an attempt to give better insights into the slagging behavior during coal/biomass combustion, an experimental investigation was conducted to study the growth of slag when coal was co-fired with wood and corn stalk in a 300 kW pilot-scale furnace. For comparison, combustion of pure coal was also conducted. During the experiments, biomass proportions of 5 and 10% by weight were examined. Slags formed on an oil cooled deposition probe were collected, sampled, and analyzed using scanning electron microscopy and X-ray diffraction (XRD). The change in slag thickness with time was obtained by a charge-coupled device monitoring system. With two thermocouples in the probe, the heat flux through the slag could be measured. The slag from pure coal combustion showed a layered structure with different levels of compactness and hardness. The heat flux decreased by 31.7% as the slag grew to 5.19 mm. The results showed that co-firing wood significantly inhibited the slagging behavior. Especially in the 10% wood case, hardly any slag was collected from the probe. Nevertheless, co-firing corn stalk resulted in severe slagging, with a slag thickness of 5.5 and 6.1 mm for two blend ratios. The formation of bubbles in the deposits together with greater deposit thickness caused heat transfer deterioration. XRD results revealed that the influence of co-firing biomass and corn stalk caused quite different changes to mineral species from wood. It was observed that fly ash under different biomass co-firing conditions differed little on mineral compositions.

The Exploration and Practice of Using Additive to Inhibit the Heating Surface Deposition in Biomass-Fired Boiler

EXPERIMENTAL STUDY OF ASH DEPOSIT DURING CO-FIRING SAWDUST AND COAL

Investigation of Ash Deposition Dynamic Process in an Industrial Biomass CFB Boiler Burning High-Alkali and Low-Chlorine Fuel

Fouling Characteristics of Coal Biomass Co-Combustion and the Influence of the Deposition Surface

Experimental study on ash deposition and corrosion in a CFB boiler co-firing biomass with coal

Study on the Deposits Derived from a Biomass Circulating Fluidized-Bed Boiler

Analysis on Deposition Mechanism of Ash with High Ash Fusion Temperatures on the Heat-insulation Layer in Boiler

Dynamic behavior of biomass ash deposition in a 25 kW one-dimensional down-fired combustor

Ash Deposition Characteristics on Heating Surface in Biomass Circulating Fluidized Bed Boiler

The effects of additives on deposit formation during co-firing of high-sodium coal with high-potassium and -chlorine biomass

Investigation of the Slagging Characteristics During Co-Combustion of Shenhua Coal and Corn Stalk: Effect of Deposition Surface

Mechanism of biomass ash slagging

Experimental Investigation of the Growth of Ash Deposits with and Without Additives Through a Digital Image Technique

Experimental Study of the Fouling Characteristics in a Pilot-Scale Facility: Influence of the Fouling Surface

Behavior of Slagging Deposits During Coal and Biomass Co-combustion in a 300 Kw Down-Fired Furnace

Investigation of Ash Deposition Characteristics in Full-Scale Circulating Fluidized Bed Boiler Burning Zhundong Coal

12th International Conference on Fluidized Bed Technology EFFECT OF ADDITIVES ON THE ASH FUSION TEMPERATURE

Co-firing biomass with coal on ash deposition behavior at various temperatures in a Down-Fired furnace

Slagging characteristics in the superheater area and K/Ca distribution of biomass-fired grate boiler

Numerical simulation of effects of flue gas recirculation on biomass combustion in grate boiler

Effects of Coal Bottom Ash on Deposit in a Full-Scale Biomass-Fired Circulating Fluidized Bed Boiler