Abstract:Cylindrical microlens arrays (CMLAs) play a key role in many optoelectronic devices, and 100% fill-factor CMLAs also have the advantage of improving the signal-to-noise ratio and avoiding stray-light effects. However, the existing preparation technologies are complicated and costly, which are not suitable for mass production. Herein, we propose a simple, efficient, and low-cost manufacturing method for CMLAs with a high fill-factor via the electric-field-driven (EFD) microscale 3D printing of polydimethylsiloxane (PDMS). By adjusting the printing parameters, the profile and the fill-factor of the CMLAs can be controlled to improve their optical performance. The optical performance test results show that the printed PDMS CMLAs have good image-projecting and light-diffraction properties. Using the two printing modes of this EFD microscale 3D-printing technology, a cylindrical dual-microlens array with a double-focusing function is simply prepared. At the same time, we print a series of specially shaped microlenses, proving the flexible manufacturing capabilities of this technology. The results show that the prepared CMLAs have good morphology and optical properties. The proposed method may provide a viable route for manufacturing large-area CMLAs with 100% fill-factor in a very simple, efficient, and low-cost manner.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c08652.EFD microscale 3D-printing principle and two printing modes; microfluidic chip structure and mixing effect verification; comparison of nanoimprint results of different hybrid methods of PDMS; effect of the nozzle size on the printing line width and height; effect of the printing height on the printing line width and height; schematic diagram of the imaging experiment of the PDMS CMLA; schematic diagram of the imaging experiment of the PDMS CMLA; and comparison of CMLAs manufactured by various technologies (PDF)High-speed photography of the micro-extrusion printing mode (MP4)Printing CMLAs with 100% fill-factor using the micro-extrusion mode (MP4)High-speed photography of the continuous cone jet printing mode (MP4)Printing CMLAs with 100% fill-factor using a continuous cone jet mode (MP4)Printing cylindrical dual-MLAs via two printing modes of EFD microscale 3D printing (MP4)Printing phoenix-shaped specially shaped microlenses by the continuous cone jet mode (MP4)Printing phoenix-shaped specially shaped microlenses by the microextrusion mode (MP4)This article has not yet been cited by other publications.

Sol–gel concave micro-lens arrays fabricated by combining the replicated PDMS soft mold with UV-cured imprint process

Elliptical Concave Microlens Arrays Built in the Photosensitive TiO2/ormosils Hybrid Films

Concave micro-lens arrays fabricated from the photo-patternable GeO 2/ormosils hybrid sol-gel films

Fabrication of micro-lens arrays built in photosensitive hybrid films by UV-cured imprinting technique

Soft Mold of Microlens Arrays Fabricated by Surface Self-Assembly

Using Micromachined Molds, Partial-curing PDMS Bonding Technique, and Multiple Casting to Create Hybrid Microfluidic Chip for Microlens Array

A Facile Method to Fabricate Close-Packed Concave Microlens Array on Cylindrical Glass

Microlens Arrays: Fabrication of Microlens Arrays with Well-controlled Curvature by Liquid Trapping and Electrohydrodynamic Deformation in Microholes (adv. Mater. 23/2012)

Facile and Flexible Fabrication of Gapless Microlens Arrays Using A Femtosecond Laser Microfabrication and Replication Process

Maskless Fabrication Of Concave Microlens Arrays On Silica Glasses By A Femtosecond-Laser-Enhanced Local Wet Etching Method

Fabrication of High-Quality Microlens Arrays on Fused Silica Based on Combined Rapid Evaporative Ablation and Precision Melting Polishing of CO2 Lasers

Single-step Fabrication of a Microlens Array in Sol–gel Material by Direct Laser Writing and Its Application in Optical Coupling

An Ultraviolet-Lithography-Assisted Sintering Method for Glass Microlens Array Fabrication

Tunable Fabrication of Concave Microlens Arrays by Initiative Cooling-Based Water Droplet Condensation.

Rapid fabrication of large-area concave microlens arrays on PDMS by a femtosecond laser

Versatile Route To Gapless Microlens Arrays Using Laser-Tunable Wet-Etched Curved Surfaces

Electrically Templated Dewetting of A Uv-Curable Prepolymer Film for the Fabrication of A Concave Microlens Array with Well-Defined Curvature

Direct Microtip Focused Electrohydrodynamic Jet Printing of Tailored Microlens Arrays on PDMS Nanofilm‐Modified Substrate

3D Printing of a PDMS Cylindrical Microlens Array with 100% Fill-Factor

Cost-efficient and Flexible Fabrication of Rectangular-Shaped Microlens Arrays with Controllable Aspect Ratio and Spherical Morphology

Fabrication of Polymer Compound Microlens by Lens-on-lens Microstructures