Abstract:The microstructure, mechanical performance, and tribological properties of SiC ceramic coatings prepared via atmospheric plasma spraying (APS) and chemical vapor deposition (CVD) method were compared to provide good anti-wear protection for carbon/carbon composites. The surface morphology of the APS-SiC coating was characterized as having a porous structure, whilst the CVD-SiC coating presented with many pyramidal-shaped crystals constituting the surface. The APS-SiC coating consists of a dominating SiC phase and a small fraction of the Si phase, while the XRD pattern of the CVD-SiC coating mainly consists of the SiC phase. The dense crystalline microstructure of the CVD-SiC coating made it possess a higher hardness and Young's modulus at 31.0 GPa and 275 GPa, respectively. The higher H/E and H3/E2 parameters of the CVD-SiC coating implied that it exhibited better plastic resistance, which is also beneficial for anti-wear properties. The scratch test reflected the critical loads of the spallation of the APS-SiC coating and CVD-SiC coating, which were evaluated to be 25.9 N and 36.4 N, respectively. In the tribological test, the friction coefficient of the APS-SiC coating showed obvious fluctuations at high load due to damage to the SiC coating. The wear mechanism of the APS-SiC coating was dominated by abrasive wear and fatigue wear, while CVD-SiC was mainly dominated by abrasive wear. The wear rate of the CVD-SiC coating was far below that of the APS-SiC coating, suggesting the better wear-resistance of the CVD-SiC coating.

Effect of Submicron and Nano SiC Particles on Erosion Wear and Scratch Behavior of Plasma-Sprayed Al 2 O 3 /8YSZ Coatings

Effect of Nano-Si3N4 Additives and Plasma Treatment on the Dry Sliding Wear Behavior of Plasma Sprayed Al2O3-8YSZ Ceramic Coatings

The Influence of Powder Types and Plasma Spray Conditions on Abrasive Wear of Nanostructured and Conventional Al2o3/Tio2 Coatings

Microstructure and abrasive resistance of ZrO2-MoSi2 coatings deposited by supersonic plasma spraying

Nanomechanical Properties and Microstructure of Zro2/Al2o3 Plasma Sprayed Coatings

The influence of powder types and plasma spray conditions on abrasive wear of nanostructured and conventional Al2O3TiO2 coatings

Microstructure, formation mechanism and properties of plasma-sprayed Cr7C3—CrSi2—Al2O3 coatings

Effects of SiC on microstructure and properties of plasma sprayed ZrB2–ZrC composite coating

Effect of Nano-meter Si3N4 on Wear Resistance and Corrosion Resistance of ZrO2-Y2O3 Ceramics Coatings

Tribological behavior of SAPS sprayed Al2O3-TiO2 and NiCr-Cr3C2 coatings under severe load conditions

Microstructure characterization of in-situ ZrC composite coating with graceful toughness and improved tribological properties prepared by plasma spraying

Microstructure and Wear Behaviors of Plasma-Sprayed MoAlB Ceramic Coating

Effect of temperature-dependent nano SiC on the ablation resistance of ZrC coating

Abrasive wear characteristics of plasma sprayed nanostructured alumina/titania coatings

A Comparison of the Tribological Properties of SiC Coatings Prepared via Atmospheric Plasma Spraying and Chemical Vapor Deposition for Carbon/Carbon Composites

Effect of Si, Al2O3 additives on the ablation behavior of ZrB2-SiC coating with Al2O3-modified SiC bond coat for C/C composites

Microstructure, Mechanical and Tribological Properties of CrSiC Coatings Sliding Against SiC and Al2O3 Balls in Water

Ablation Mechanism and Elevated Ablation Resistance of In-Situ Zrc-Zrsi2 Composite Coating Prepared by Plasma Spraying

Solid Particle Erosion Behavior of NiCr-Al<sub>2</sub>O<sub>3</sub>-ZrO<sub>2</sub> (8Y) Ceramic Composites

Cathode plasma electrolytic deposition of Al2O3 coatings doped with SiC particles

Microstructure and Properties of Al2O3–ZrO2–Y2O3 Composite Coatings Prepared by Plasma Spraying