Abstract:Titanium alloys have been applied for many lightweight structural components in the fields of aerospace, automobiles and biomedical implants owing to their light-weight, good mechanical properties and biocompatibility. However, poor tribological performance often restricts their wide-range applications. In this study, we synthesized Cu modified Ti-6Al-4V (TC4) powders with various Cu contents (0, 1, 3, 5, 10 wt%), which was further strengthened with 0.3 wt% graphene oxide nanosheets (GONs) using a powder metallurgy technology. These composite powders were then synthesized into titanium matrix composites using spark plasma sintering. Effects of Cu contents on microstructure evolution, phase composition and tribological properties of Ti matrix composites were systematically investigated. The synthesized composites were consisted of α-Ti, β-Ti, Ti2Cu, in-situ-formed TiC and remained GONs, and showed better tribological properties than those of TC4 alloy. The average coefficient of friction was reduced from 0.168 to a minimum value of 0.120 as the copper content increased from 0 to 3 wt%, meanwhile the wear volume loss was reduced by 49.3%. Whereas further increasing Cu contents resulted in the increases of both coefficients of friction and wear volume loss. These improvements are mainly attributed to the hardness strengthening effects by Ti-Cu intermetallics and structure, as well as the self-lubricating effect of GONs. Compared with traditional surface modification processes, the new method proposed in this work is cost-effective and promising for improving the tribological performance of titanium alloys in industry applications.

Effects of TiN nanoparticles on the microstructure and properties of W–30Cu composites prepared via electroless plating and powder metallurgy

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

The Influence of TiB2 Content on Microstructure and Properties of W–30Cu Composites Prepared by Electroless Plating and Powder Metallurgy

Influence of TiC Content on Microstructure and Properties of W-30Cu/TIC Composites

Effect of Silver Element on Microstructure and Properties of W-30Cu/TiC Composites

Influence of TiN nanoparticles on the microstructure and properties of W matrix materials prepared by spark plasma sintering

Influence of TiC Content on Microstructure and Properties of W-3OCu/TiC Composites

Effect of Ni Content on Microstructure and Properties of WC-Ni Composites Prepared by Electroless Plating and Powder Metallurgy

Effect of TiN concentration on microstructure and properties of Ni/W–TiN composites obtained by pulse current electrodeposition

Effect of Electroless Cu Plating Ti3AlC2 Particles on Microstructure and Properties of Gd2O3/Cu Composites

Sintering Behavior of W–30Cu Composite Powder Prepared by Electroless Plating

Effect of Doped Niobium on the Microstructure and Properties of W–Nb/TiC Composites Prepared by Spark Plasma Sintering

Effect of Pulse Electrodeposition Mode on Microstructures and Properties of Ni-TiN Composite Coatings

Microstructure and Properties of TiN-reinforced W–Ti Alloys Prepared by Spark Plasma Sintering

Preparation and organization of W-Ni/TiC composite material

Preparation and properties of Ni-W-P-TiO2 nanocomposite coatings developed by a sol-enhanced electroplating method

Microstructure and tribological properties of titanium matrix nanocomposites through powder metallurgy using graphene oxide nanosheets enhanced copper powders and spark plasma sintering

Preparation and Properties of W-15Cu Composite by Electroless Plating and Powder Metallurgy

Effect of nano-Y2O3 on the microstructure and mechanical properties of Cu-10W composites prepared by spark plasma sintering

Microstructure and properties of Cu-Sn-Zn-TiO2 nano-composite coatings on mild steel

Preparation and Characterization of Nanostructured Ni-TiN Composite Films