Abstract:Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) was developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) were comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibited a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at −20 °C. In contrast, the HR-QT steel exhibited tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consisted of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reached 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared with the HR-QT process, the TMCP-DQP process resulted in a finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieved the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilized the RA through carbon enrichment, while the relaxation stage reduced a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminated internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

Microstructure and Mechanical Behaviour of Ultra-High Strength of Fine-Grained AISI 4140 Steel

Effect of Heavy Warm Rolling on Microstructures and Mechanical Properties of AISI 4140 Steel

Mechanical behavior and strengthening mechanism of a fine-grained medium carbon steel produced via cyclic oil quenching

Achieving 2.2 GPa Ultra-High Strength in Low-Alloy Steel Using a Direct Quenching and Partitioning Process

Composition and Processing of Direct-Quench Hot Rolled Steels with Ultrahigh Strength Exceeding GPa

An Ultrahigh-Strength Steel Produced by Heavy Warm Rolling of the Metastable Austenite

Study of Quenching and Partitioning (Q&P) and Ultrasonic Surface Rolling (USR) Process on Microstructure and Mechanical Property of a High-Strength Martensitic Steel

Achieving ultrahigh strength by tuning the hierarchical structure of low-carbon martensitic steel

Hot-Rolling and a Subsequent Direct-Quenching Process Enable Superior High-Cycle Fatigue Resistance in Ultra-High Strength Low Alloy Steels

Study of microstructures and deformation behavior of ultrafine-grained high-Mn TWIP steel fabricated by heavily asymmetric-symmetric rolling

Achieving Fine-Grained Microstructure and Superior Mechanical Property in a Plain Low-Carbon Steel Using Heavy Cold Rolling Combined with Short-Time Heat Treatment

Effect of Annealing on Microstructure and Mechanical Properties of Ultrafine-Grained Low-Carbon Medium-Manganese Steel Produced by Heavy Warm Rolling

On the Strain Hardening and Tensile Properties of AISI 4140 Steel via Single‐Step Quenching and Partitioning Treatments

Microstructure and mechanical properties of a low-carbon HDQ&P steel

An Investigation on the Microstructure and Mechanical Properties in an Ultrafine Lamellar Martensitic Steel Processed by Heavy Warm Rolling and Tempering

The Microstructural design and control of ultrahigh strength-ductility martensitic steels based on a novel quenching-partitioning-tempering process

Microstructures and Deformation Behavior of Nano-Grained and Ultrafine-Grained High-Mn Austenitic Steel Fabricated by Asymmetric-Symmetric Rolling

Achieving 1.7 GPa Considerable Ductility High-Strength Low-Alloy Steel Using Hot-Rolling and Tempering Processes

Analysis of Microstructure and Mechanical Properties of Ultrafine Grained Low Carbon Steel

Strength‐Ductility Synergy in an Austenitic Stainless Steel Processed by Warm Rolling and Subsequent Cryogenic Treatment

Enhanced mechanical properties of a high-carbon martensite steel processed by heavy warm rolling and tempering