Abstract:The warm‐rolled and cryogenically treated sample achieved exceptional mechanical properties, with a yield strength of ≈949 MPa and elongation of ≈56.2%. Its high strength stems from grain refinement, increased dislocation density, and martensite formation via cryogenic treatment. Deformation is stage‐dependent: early dislocation slip, mid‐stage transformation‐induced plasticity (TRIP) effect, and late‐stage martensite slip. Fine grains delay TRIP, enhancing ductility. The austenitic stainless steel undergo warm rolling, followed by cryogenic treatment. The warm‐rolled and cryogenically treated (WR‐CT) sample exhibits superior strength and ductility compared to the warm‐rolled (WR) sample, achieving a yield strength of 949 MPa and an elongation of ≈56.2%. The enhanced strength is attributed to the higher dislocation density, additional grain refinement, and the presence of martensite in the WR‐CT sample. The WR and WR‐CT samples exhibit similar deformation mechanisms. In the initial stage, dislocation slip predominantly governs the deformation. During the intermediate stage, the transformation‐induced plasticity (TRIP) effect dominates the deformation mechanism. In the final stage, nearly all austenite transforms into martensite, and deformation mainly occurs via dislocation slip within the martensite phase. However, in the WR‐CT sample, the TRIP effect is delayed during the stable processing stage (≈8–23%) due to the higher mechanical stability of austenite, resulting from further grain refinement and higher dislocation density. Additionally, the coordinated deformation of strain‐induced martensite with varying orientations contributes to delayed necking, achieving an optimal balance between strength and ductility.

Ultrafine lamellar microstructure with greatly enhanced strength and ductility of martensite steel via heavily warm rolling of metastable austenite

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Influence of warm rolling temperature on multi-scale lamellar structure and mechanical properties of medium carbon steel

Enhanced mechanical properties of a high-carbon martensite steel processed by heavy warm rolling and tempering

Microstructure evolution and mechanical properties of metastable austenitic medium Mn steel fabricated by warm caliber rolling

Achieving ultrahigh strength by tuning the hierarchical structure of low-carbon martensitic steel

Ultrafine Structure and High Strength in Cold-Rolled Martensite

Enhanced strength and ductility of the low-carbon steel with heterogeneous lamellar dual-phase structure produced by cyclic intercritical rolling

Effects of prior austenite refinement on microstructure and property of ultra-fine lath martensitic steel

Microstructural Evolution and Mechanical Properties of 6cr13 Martensitic Stainless Steel Subjected to Cold Rolling and Heat Treatments

Achieving Unexpected Strength and Ductility Synergies in Heterogeneous Metastable Lamellar Steels

Shaping mechanism of ultrafine metastable austenite in HSLA steels through a cumulative process of hot rolling, partitioning and tempering

Ultra-Fine Heterogeneous Microstructure Enables High Strength-Ductility in a Cold-Rolled Medium Mn Steel

Hierarchical Multiple Precursors Induced Heterogeneous Structures in Super Austenitic Stainless Steels by Cryogenic Rolling and Annealing

Development of Very Tough Ferritic Stainless Steels by Optimizing the Recrystallized Microstructure

Heterogeneous Multi-Phase Grains Improving the Strength-Ductility Balance in Warm-Rolled Fe-18Mn-3Ti Steel

Microstructural evolution and strain hardening behavior of a novel two-stage warm rolled ultra-high strength medium Mn steel with heterogeneous structures

Preparation and Mechanical Behavior of Ultra-High Strength Low-Carbon Steel

Strength‐Ductility Synergy in an Austenitic Stainless Steel Processed by Warm Rolling and Subsequent Cryogenic Treatment

Enhanced mechanical properties of ultrafine-lamella 304L stainless steel processed by multidirectional hot forging

Overcoming the strength-ductility trade-off in metastable dual-phase heterogeneous structures using variable temperature rolling and annealing