Abstract:Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) was developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) were comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibited a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at −20 °C. In contrast, the HR-QT steel exhibited tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consisted of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reached 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared with the HR-QT process, the TMCP-DQP process resulted in a finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieved the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilized the RA through carbon enrichment, while the relaxation stage reduced a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminated internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

Attainment of an exceptionally high strength in low-carbon steel along with modest ductility through a novel heat treatment route

A cryogenic ultra-strong and ductile steel induced by stable nanoscale dual-phase structure

The Fabrication of Ultrahigh-Strength Steel with a Nanolath Structure via Quenching-Partitioning-Tempering

Microstructural modifications and changes in mechanical properties during cyclic heat treatment of 0.16% carbon steel

Achieving ultrahigh strength by tuning the hierarchical structure of low-carbon martensitic steel

Tailoring Low‐Alloyed Cryogenic Steel Strong and Tough Introduces Fine‐Grained Equiaxed Ferrite by Intercritical Subquenching

Microstructure Features and Tensile Properties of a Recent Ultra-High-Strength Steel via Two-Step Quenching and Partitioning Process

Revealing the mechanism of extraordinary hardness without compensating the toughness in a low alloyed high carbon steel

Achieving 2.2 GPa Ultra-High Strength in Low-Alloy Steel Using a Direct Quenching and Partitioning Process

Mechanical behavior and strengthening mechanism of a fine-grained medium carbon steel produced via cyclic oil quenching

Enhanced mechanical properties of a high-carbon martensite steel processed by heavy warm rolling and tempering

Development of ultra high strength steel with high ductility by air cooling post single stage quench partitioning

A novel microstructural design and heat treatment technique based on gradient control of carbon partitioning between austenite and martensite for high strength steels

Low-Carbon Bainite Steel with High Strength and Toughness Processed by Recrystallization Controlled Rolling and Ultra Fast Cooling (RCR+UFC)

Role of nano-bainite laths and nanosized precipitates: Strengthening a low-alloy steel to 1870 MPa

Process control maps to design an ultra-high strength-ductile steel

Increasing the Strength and Impact Toughness of Carbon Steel Using a Nanosized Eutectoid Resulting from Time-Controlled Quenching

Strength‐Ductility Synergy in an Austenitic Stainless Steel Processed by Warm Rolling and Subsequent Cryogenic Treatment

Nanoscale austenite reversion through partitioning, segregation, and kinetic freezing: Example of a ductile 2 GPa Fe-Cr-C steel

Tailoring Strength and Ductility of a Cr-Containing High Carbon Steel by Cold-Working and Annealing

Increase in Low-Carbon Steel 12GBA Strength and Cold Resistance by a Deformation-Thermal Effect