Abstract:In this work, the SnO 2 -Ti 3 C 2 hybrid electron transport layer (ETL) was prepared by incorporating two-dimensional Ti 3 C 2 -MXene into SnO 2 and appropriate ultraviolet (UV) ozone treatment. The synergistic effect of Ti 3 C 2 introduction and UV ozone treatment on the charge transport capacity of SnO 2 ETL, interface properties of ETL/perovskite, perovskite morphology, and device performance was systematically investigated. The results show that the introduction of Ti 3 C 2 does not affect the morphology and transmittance of SnO 2 ETL. The perovskite films based on SnO 2 -Ti 3 C 2 are not only dense, but also have smaller surface roughness, more uniform, and larger grain size, even penetrating the entire perovskite film. The surface oxidation of Ti 3 C 2 induced by UV-ozone treatment enhanced the charge transport capacity of ETL. The electron extraction and charge transfer at the interface between SnO 2 -Ti 3 C 2 ETL and perovskite are higher, and carrier recombination is effectively suppressed. Perovskite solar cells (PSCs) based on SnO 2 -Ti 3 C 2 ETL have larger charge recombination impedance and higher electron mobility, mainly due to enhanced ETL charge transport and optimization of interface properties. The short-circuit current ( J sc) and filling factor (FF) of PSCs are increased by 5% and 7% respectively, delivering a champion device with a relatively high FF of 79.38% and high power conversion efficiency of 19.52%, as well as good stability. Thus, this study provides a simple and effective method for the preparation of efficient and repeatable PSCs and paves the way for the industrialization of PSCs to a certain extent.

Mesoporous SnO₂ Single Crystals As an Effective Electron Collector for Perovskite Solar Cells.

Enhancing Electron Extraction and Transport in Inorganic Perovskite Solar Cells Via Additional Built-in Potential of SnO2-BiFeO3 Nano-Heterostructure

Core-Shell ZnO@SnO2 Nanoparticles for Efficient Inorganic Perovskite Solar Cells.

Polysaccharide Modified SnO2 for Highly Efficient Perovskite Solar Cells

Enhanced Lifetime and Photostability with Low-Temperature Mesoporous ZnTiO3 /Compact SnO2 Electrodes in Perovskite Solar Cells

Electrochemical Reduction and Ion Injection of Annealing‐Free SnO2 for High Performance Perovskite Solar Cells

Single Source, Surfactant‐Free, and One‐Step Solvothermal Route Synthesized TiO 2 Microspheres for Highly Efficient Mesoscopic Perovskite Solar Cells

Polyelectrolyte-Doped SnO<sub>2</sub> as a Tunable Electron Transport Layer for High-Efficiency and Stable Perovskite Solar Cells

Enhanced Electronic Properties of SnO2 via Electron Transfer from Graphene Quantum Dots for Efficient Perovskite Solar Cells.

Low-Temperature-Processed Monolayer Inverse Opal SnO2 Scaffold for Efficient Perovskite Solar Cells

SnO2-Ti3C2 Blends As Electron Transport Layer for Efficient and Easily Fabricated Planar Perovskite Solar Cells

Bifunctional SnO 2 Colloid Offers No Annealing Effect Compact Layer and Mesoporous Scaffold for Efficient Perovskite Solar Cells

Well-organized SnO2 inverse opal monolayer as structured electron transport layer for high-efficiency perovskite solar cells

SnO2 modified mesoporous ZrO2 as efficient electron-transport layer for carbon-electrode based, low-temperature mesoscopic perovskite solar cells

Rational design of SnO 2 -based electron transport layer in mesoscopic perovskite solar cells: more kinetically favorable than traditional double-layer architecture

SnO x as Bottom Hole Extraction Layer and Top In Situ Protection Layer Yields over 14% Efficiency in Sn-Based Perovskite Solar Cells

cPCN-Regulated SnO2 Composites Enables Perovskite Solar Cell with Efficiency Beyond 23%

MXene-based novel nanocomposites doped SnO2 for boosting the performance of perovskite solar cells

Mesoporous structured MoS2 as an electron transport layer for efficient and stable perovskite solar cells

Multifunctional Regulation of Chemical Bath Deposition Based SnO2 for Efficient Perovskite Solar Cells.

Synergistical Transition Metal Ion Co-Doping and Multiple Functional Additive Passivation for Realizing 25.30% Efficiency Perovskite Solar Cells