Abstract:In this study, the cooperative effect of Mg and Si contents on the microstructural evolution, mechanical properties, and deformation behavior of the cast Al–Li–Mg–Si alloys is investigated. Five different Al–Li–Mg–Si alloys are prepared by conventional casting method, which are referred to as Alloy A-E. The results show that with the increase in the Mg content, the amount of lath-like Mg2Si precipitates and bulk-like AlLiSi particles increases, which leads to an improvement in the strength and ductility of alloys. The amount of intergranular Si-rich phases in Alloy D increases with the increase in the Si content. Further, a higher Si content in Alloy E promotes the formation of bulk-like AlLiSi. The geometric phase analysis (GPA) results reveal strain partitioning behavior at the interface of Mg2Si precipitates and AlLiSi particles, which follows the Orowan looping or dislocation cutting strengthening mechanism. The geometrically necessary dislocation (GND) density calculation results suggest that the lath-like Mg2Si precipitates play a critical role in the deformation behaviors of Alloy A-C. The hindering effect of lath-like Mg2Si precipitates on the movement of dislocations decreases the GND density gap between high-angle grain boundaries or junctions and grain interior and improves the resistance to deformation. However, the deformation behaviors of Alloy D and E with higher Si content are mainly governed by the intergranular Si-rich phases. Finally, a methodological framework is established to elucidate the effect of precipitates and/or intergranular phases on the deformation behaviors of materials using a combination of GPA and GND density calculation methods.

Effect of Si Content on Dynamic Recrystallization of Al-Si-Mg Alloys During Hot Extrusion

Effect of Mg on Nucleation Process of Recrystallization in Al–Mg–Si/SiCp Composite

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Hot deformation and dynamic recrystallization in Al-Mg-Si alloy

Effects of Reinforced Particles on Dynamic Recrystallization of Mg Base Alloys During Hot Extrusion

Simulation of dynamic recrystallization in an Al-Mg-Si alloy during inhomogeneous hot deformation

Hot deformation behaviour and microstructure evolution of Al-3%Mg2Si alloy

The Effect of Multidirectional Forging on the Microstructure and Superplasticity of the Al–Mg–Si–Cu System Alloys with Different Contents of Mg and Si

Investigation on the Grain Structure Evolution and Abnormal Stress Increase of Al–Mg–Si Alloy During Hot Deformation

Effects of Si content on microstructure and mechanical properties of Mg-Gd-Y-Zr casting alloy

Cooperative Effect of Mg and Si Contents on the Microstructural Evolution, Mechanical Performance, and Deformation Behavior of Cast Al–Li–Mg–Si Alloys

Grain Growth and Recrystallization Behaviors of an Ultrafine Grained Al-0.6 Wt%mg-0.4 Wt%si-5Vol.%sic Nanocomposite During Heat Treatment and Extrusion

Effects of Dynamic Recrystallization in Extruded and Compressed Az31 Magnesium Alloy

Effect of Microstructure on the Precipitation of β-Mg2Si during Cooling after Homogenisation of Al-Mg-Si Alloys

Characterization and Calculation of the Dynamic Recrystallization Texture in Fe-3.0 Wt.% Si Alloy

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

Effect of Sm content on microstructure and properties of extruded Mg-6Al-2Sr alloy

Effect of Minor Elements Content on the Phase Formation and Mechanical Properties of 6xxx Series Aluminum Alloy Sheets

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Effect of Extrusion Temperature on Microstructural Evolution and Intergranule Bonding of Al–7Si–0.3Mg (wt%) Alloy Rods Produced by Extrusion of Granule Compacts

Effect of Hot Extrusion on Microstructures and Mechanical Properties of SiC Nanoparticles Reinforced Magnesium Matrix Composite