Abstract:The present work is focused on the multidirectional forging (MDF) of Al–20 wt-% Si alloys with the addition of refiners and modifiers. The MDF process was performed at 200°C with a cumulative strain of 0.63. Microstructural characterization and mechanical performance were evaluated on the Al–20Si, Al–20Si–4.5Cu, Al–20Si–4.5Cu–1(Al–Ti–B), Al–20Si–4.5Cu–1(Al–Ti–B)–10(Al–Sr). The microstructure analysis revealed significant changes in the eutectic and primary phase refinement. The micro-Vickers hardness confirmed that the MDF process resulted in increased hardness (125 ± 1.9 VHN) compared to the homogenized samples (96 ± 2.7 VHN). Tensile test results showed that with the accumulation of strain, ultimate tensile strength increased to 435 MPa from 302 MPa with reduction in the percentage of elongation from 7.8 to 5.6. The grains were more uniformly distributed with addition of modifiers, and refiners further reduced the nucleation number of eutectic grains. The wear study demonstrated that the wear resistance is more in the Al–Si-Cu-Sr sample due to the increased level of hardness. The combination of multidirectional forging techniques with judicious incorporation of refiners and modifiers engenders a synergistic enhancement of microstructural integrity, hardness profiles, and wear-resistant properties in hypereutectic Al-20Si alloys. Le travail courant se concentre sur le forgeage multidirectionnel (MDF) des alliages Al-20% en poids Si avec ajout d'agents d'affinage et modificateurs. On a réalisé le procédé MDF à 200°C sur trois passes avec une déformation cumulée de 0.63. Suite au procédé MDF, on a évalué la caractérisation microstructurale et les performances mécaniques sur Al–20Si, Al–20Si–4.5Cu, Al–20Si–4.5Cu–1(Al–Ti–B) et Al–20Si–4.5Cu–1(Al–Ti–B)–10(Al–Sr). L'analyse de la microstructure a révélé des changements significatifs dans le raffinement de la phase eutectique et primaire après le traitement MDF. Les essais de microdureté Vickers ont confirmé que le procédé MDF entraînait une dureté accrue (125 ± 1.9 VHN) par rapport aux échantillons homogénéisés (96 ± 2.7 VHN). Les résultats des essais de traction ont montré qu'avec l'accumulation de déformation, la résistance ultime à la traction a augmenté de 302 MPa à 435 MPa avec une réduction du pourcentage d'allongement de 7.8 à 5.6. Les grains étaient distribués plus uniformément avec l'ajout d'agents modificateurs, et les agents d'affinage ont réduit davantage le nombre de nucléation des grains eutectiques. L'étude d'usure a démontré que la résistance à l'usure est supérieure dans l'échantillon Al–Si–Cu–Sr en raison du niveau de dureté accru. La combinaison des techniques de forgeage multidirectionnel avec l'incorporation judicieuse d'agents d'affinage et modificateurs engendre une amélioration synergique de l'intégrité microstructurale, des profils de dureté et des propriétés de résistance à l'usure des alliages hypereutectiques Al–20Si.

The Effect of Multidirectional Forging on the Microstructure and Superplasticity of the Al–Mg–Si–Cu System Alloys with Different Contents of Mg and Si

Effect of Mg on Nucleation Process of Recrystallization in Al–Mg–Si/SiCp Composite

Effect of Multidirectional Isothermal Forging on the Formation of Ultrafine-Grained Structure in Alloy 1570C

Effect of Multidirectional Forging on the Microstructures and Mechanical Properties of the Al–Mg–Si Alloy

Effect of multidirectional forging on grain structure and mechanical properties of hypereutectic Al–20%Si alloys with added refiners and modifiers

Development of Ultrafine Grain Structure in an Al–Mg–Mn–Sc–Zr Alloy During High-Temperature Multidirectional Isothermal Forging

Mechanism of Ductility Enhancement of the Mg-8Gd-4Y-1Nd-0.5Si Alloy by Multi-Directional Forging Process before Extrusion

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

Prominent role of multi-scale microstructural heterogeneities on superplastic deformation of a high solid solution Al–7Mg alloy

Effect of Multidirectional Isothermal Forging on Microstructure and Mechanical Properties in Ti-6Al-4V Alloy

Microstructure and Mechanical Properties of Al-Cu-Mn Alloy Mechanically Alloyed with 5 wt% Zr After Multi-Directional Forging

The multi-scale Si-containing phases-assisted improvement in the microstructure and mechanical properties of Al–Mg-xSi-Cu-Zn alloys

Influence of Forging Temperature on the Microstructures and Mechanical Properties of a Multi-Directionally Forged Al–Cu–Li Alloy

High Strain Rate Quasi-Superplasticity Behavior in an Ultralight Mg-9.55Li-2.92Al-0.027Y-0.026Mn Alloy Fabricated by Multidirectional Forging and Asymmetrical Rolling

Quantitative analysis of influence of α-Al(MnFeCr)Si dispersoids on hot deformation and microstructural evolution of Al-Mg-Si alloys

Effect of Mg addition on microstructure and mechanical properties of Al-Si-Cu-Fe alloy with squeeze casting

Formation of Phases and Microstructures in Al-8Si Alloys with Different Mg Content

Effect of ultrasonic melt processing and cooling rate on microstructure evolution of Al–Cu–Mn–Mg–Fe–Si alloy

Relationship between Microstructure Evolution and Tensile Properties of AlSi10Mg Alloys with Varying Mg Content and Solidification Cooling Rates

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Effect of final rolling deformation on microstructure, work hardening and softening behavior of Mg-8Li-3Al-0.3Si alloys