Abstract:In this study, equal channel angular pressing (ECAP) was applied to a hot-extruded Mg–5.00Zn–0.92Y–0.16Zr (wt.%) alloy to produce an ultrafine-grained a-Mg structure of 0.6μm with uniformly distributed fine quasicrystal Mg3YZn6 particles. The basal planes in the as-ECAPed alloy were inclined approximately 45° to the ECAP direction (EPD); thus, a high Schmid factor of 0.36 for (0001)〈112¯0〉 basal slip along EPD was obtained. Then, the superplastic behavior at low temperatures of 150–250°C and initial strain rates of 1.67×10−3s−1–1.67×10−1s−1 of the as-ECAPed alloy was investigated and compared with that of the as-extruded alloy. The microstructural development, texture evolution and cracking behavior during tensile tests were systemically investigated by electron backscattered diffraction (EBSD) analysis. During the tensile test along the EPD, the basal planes in the as-ECAPed alloy specimen were tilted approximately 15° away from the original position; thus, the basal planes were still in a position favorable for the basal slip along the EPD. As a result, a maximum elongation of 865% was obtained at 200°C and a strain rate of 1.67×10−3s−1, as a result of this favored basal texture and the excellent thermal stability of the ultrafine-grained structure. This optimum superplastic temperature of 200°C is much lower than that obtained for other Mg–Zn–Y–(Zr) alloys. In contrast, for the as-extruded alloy specimen, superplastic behavior did not occur until the critical condition of 250°C and a strain rate of 1.67×10−3s−1. Below this temperature and strain rate, the strong extrusion basal texture was maintained, and the cracks in the hot-worked coarse region (or un-DRXed region) were observed nucleating mainly associated with the formation of a 38° {101¯1}–{101¯2} double twin. At this temperature and strain rate, the hot-worked coarse regions were significantly refined by the dynamic recovery and the following recrystallization process. In the case, the formation of a double twin was prevented and the facture was delayed.

Optimizing Superplasticity of AZ91−xSn Magnesium Alloys with Competitive Grain Growth and Boundary Sliding

Enhanced superplasticity achieved by disclination-dislocation reactions in a fine-grained low-alloyed magnesium system

Superplasticity and Grain Boundary Sliding in Rolled AZ91 Magnesium Alloy at High Strain Rates

Superplastic Behavior and Microstructural Evolution in a Commercial Mg-3Al-1Zn Magnesium Alloy.

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

Effect of Sc and Zr Additions on Grain Stability and Superplasticity of the Simple Thermal–mechanical Processed Al–Zn–Mg Alloy Sheet

Superplastic behavior and microstructural evolution in a commercial Mg-3Al-1Zn magnesium alloy : Superplasticity and its applications

Realizing impressive superplasticity in a low-alloyed Mg-Zn-Ca-Al-Mn alloy: The roles of grain boundary segregation and dense β-Mn particles

Prominent Role of a High Volume Fraction of Mg17Al12 Particles on Tensile Behaviors of Rolled Mg–Al–Zn Alloys

Refined microstructure and improved mechanical properties of high-ratio extruded AZ91−xSn magnesium alloy

Solute Segregation Assisted Superplasticity in a Low-Alloyed Mg–Zn–Ca–Sn–Mn Alloy

Achieving Fine Grain Structure and Superplasticity in AZ91-0.4Sn Magnesium Alloy Using Short Flow Rolling Process

Achieving Superplasticity in AZ31 Magnesium Alloy Processed by Hot Extrusion and Rolling

Superplastic Behavior and Microstructure Evolution of A New Al-Mg-Sc-Zr Alloy Subjected to A Simple Thermomechanical Processing

Excellent superplasticity and deformation mechanism of Al–Mg–Sc–Zr alloy processed via simple free forging

Superplasticity of Mg-5.8Zn-1Y-Zr Alloy Sheet Fabricated by Combination of Extrusion and Hot-Rolling Processes

Superplastic Deformation Behavior of Rolled Mg-8Al-2Sn and Mg-8Al-1Sn-1Zn Alloys at High Temperatures

High Strain Rate Superplasticity of Rolled AZ91 Magnesium Alloy

Achieving Low-Temperature Superplasticity of a Coarse-Grained BAZ531 Magnesium Alloy

Superplastic Behavior of Fine-Grained Extruded ZK61 Mg Alloy

The Microstructural Evolution and Superplastic Behavior at Low Temperatures of Mg–5.00Zn–0.92Y–0.16Zr (wt.%) Alloys after Hot Extrusion and ECAP Process