Abstract:Effects of Zn/Al mass ratio on the microstructure evolution and mechanical properties of the Mg-3Sn-5Zn-xAl (x=0,1,2,3 wt%) alloy were systematically investigated in the present study. The secondary phases of as-cast alloys were transformed from MgZn2/alpha-Mg eutectics and Mg2Sn to icosahedral (I-) phase and Mg2Sn with decreasing of Zn/Al mass ratio. After extrusion, almost completely recrystallized fine grains were obtained in TZ35-xAl alloys, but the volume fraction of recrystallized region was slightly reduced by the addition of Al. This phenomenon was chiefly ascribed to the particle-stimulated nucleation (PSN) mechanism and Zener grainboundary pinning effect induced by enormous numbers of fine Mg-Zn phase, I-phase, Mg2Sn and newly formed iii-phase (related to I-phase) particles. As-extruded alloys exhibited superior strength and ductility balance. Specifically, Mg-3Sn-5Zn-1Al alloy got the highest ultimate tensile strength and elongation, reaching 340 MPa and 20.1%, respectively. Moreover, tensile yield strength of as-extruded alloys rises dramatically from 169 MPa to 212 MPa along with rising of the Al level. Improved tensile yield strength is primarily attributed to the synergistic reinforcement mechanism of grain refinement and dynamic precipitation of fine secondary particles. The excellent ductility for all as-extruded alloys owes a great deal to the activation of non-basal slip systems, high volume fraction of fine DRXed grains and weakened texture.

Microstructure and Mechanical Properties of Asextruded Mg–xAl–5Sn–0·3Mn Alloys (x = 1, 3, 6 and 9)

Microstructures and mechanical properties of as-extruded Mg–5Sn–1Zn–xAl (x=1, 3 and 5) alloys

Microstructure and Mechanical Properties of Mg–Al–Sn Extruded Alloys

Microstructures and Mechanical Properties of Mg–xAl–1Sn–0.3Mn (x = 1, 3, 5) Alloy Sheets

Microstructure and Mechanical Properties of Mg–6Li–xAl–0.8Sn Alloys

Microstructures and Mechanical Properties of As-Extruded and Heat Treated Mg–6Zn–1Mn–4Sn–1.5Nd Alloy

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Effect of Al on Microstructure and Mechanical Properties of As-Extruded Mg–1Mn Alloy Sheet

Microstructure and mechanical properties of as-cast and extruded Mg-8Li-1Al-0.5Sn alloy

Strong and Ductile Mg-0.4Al Alloy with Minor Mn Addition Achieved by Conventional Extrusion

Effect of Al on the Microstructure and Mechanical Properties of Mg–6Zn–2Sn–0.5Mn Alloy

Microstructure and Mechanical Behavior of Mg-0.5Si-xSn Alloys

Microstructures and Mechanical Properties of Hot-extruded Mg-6Zn-xCu-0.6Zr(x=0,0.5,1.0,1.5) Alloys

Effects of Zn/Al Mass Ratio on Microstructure Evolution and Mechanical Properties of Mg–Sn Based Alloys

Microstructure and Strengthening Mechanism of Hot-Extruded Ultralight Mg-Li-Al-Sn Alloys with High Strength

Effect of Mn Content on the Microstructure and Mechanical Properties of Mg–6Li–4Zn-xMn Alloys

Microstructure and Mechanical Properties of Mg–6Al–1Sn–0.3Mn Alloy Sheet Fabricated Through Extrusion Combined with Rolling

Microstructure, Texture, and Mechanical Properties of As-Extruded Mg-xLi-3Al-2Zn-0.2Zr Alloys (x = 5, 7, 8, 9, 11 Wt%)

Medium-strength and high-plasticity Mg–Sn-based alloys

Microstructures and Mechanical Properties of Mg-2Y-xZn (x=1, 2, 3 At%) Alloys

Microstructure, Mechanical Properties, and Strengthening Mechanisms of Extruded Mg-1Nd-1Mn Alloys with Different Zn