Abstract:Mg–1Mn alloy, extruded at a low temperature in our published protocol, contributed to the intensified basal texture and extremely refined microstructure with spheroidal nanoscale precipitates dispersing throughout the matrix and along the grain boundaries, consequently resulting in the excellent mechanical properties where the alloy exhibited a tensile yield strength of 204.3 MPa and a ductility of 38.8% at room temperature. Therefore, Mg–1Mn alloy was recommended as one of the potential materials for structural applications. In the present investigation, hot deformation behavior through constitutive analysis and extrusion temperature-dependent microstructure, texture and mechanical properties of as-extruded Mg–1Mn alloy were investigated, aiming at revealing how extrusion temperature affected microstructure, texture, and mechanical properties of as-extruded Mg–1Mn alloy. X-ray diffraction patterns demonstrated that phase components of the experimental alloys consisted of the α-Mg matrix and Mn precipitates. Optical microscopy images indicated a significant increase in average grain size of the alloys as the extrusion temperature increasing from 250 °C to 400 °C. Scanning electron microscopy graphics revealed that coarsened particles identified as Mn precipitates by EDS were observed within the matrix when extrusion temperature reached 400 °C. Inverse pole figure maps of the experimental samples subjected to different extrusion temperatures in the present work exhibited the typical basal texture, suggesting that basal slip was activated hardly during the tensile stress applied along the extrusion direction. Consequently, extrusion temperature displayed the significant impact on microstructure, texture, and mechanical properties of as-extruded Mg–1Mn alloy. The alloy extruded at both 250 °C and 300 °C exhibited the strong basal texture and refined microstructure with spheroidal nanoscale precipitates dispersing within the matrix and along the grain boundaries, which contributed to their excellent comprehensive mechanical properties. The alloy extruded at 400 °C possessed the typical basal texture and coarsened microstructure, leading to the extremely poor mechanical properties. Simultaneously, the constitutive model of the Arrhenius equation based on Zener-Hollomon parameters was also established in the present investigation. Therefore, optimizing the extrusion temperature to regulate the microstructure, grain orientation distribution, and morphology of precipitates was considered as one of the effective approaches for achieving the excellent mechanical properties of Mg alloys.

Effect of Al on Microstructure and Mechanical Properties of As-Extruded Mg–1Mn Alloy Sheet

Effect of Al on the Microstructure and Mechanical Properties of Mg–Sn–Ca–Mn Wrought Alloy

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Effect of Mn content on the microstructure and mechanical properties of as-extruded Zn-0.2Mg-Mn (wt%) alloys

Effect of Ca/Al Ratio on Microstructure and Mechanical Properties of Mg-Al-Ca-Mn Alloys

Enhanced Strength by Precipitate Modification in Wrought Mg–Al–Ca Alloy with Trace Mn Addition

Effects of Sn and Mn Addition on the Microstructure and Mechanical Properties of As-Extruded Mg–2Al–1Zn Alloys

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Microstructure and Tensile Properties of Al-Mg-Mn Alloy

Effects of Mn Addition on the Microstructure and Mechanical Properties of Cast Mg–9Al–2Sn (wt.%) Alloy

The investigation on microstructure evolution and mechanical behavior of extruded Mg-1.5Al-xLa-Mn (x=0.5, 1, 2wt%) alloys

Hot deformation behavior and extrusion temperature-dependent microstructure, texture and mechanical properties of Mg–1Mn alloy

Microstructure and Mechanical Properties of Extruded Mg–Zn–Mn–Ca Alloys

Ultrahigh Strength Mg-Al-Ca-Mn Extrusion Alloys with Various Aluminum Contents

Mechanical Properties and Microstructures of Mg-Al-Zn Alloys with High Aluminum Contents

Influence of Ca Content on Microstructure and Mechanical Properties of Extruded Mg–Al–Ca–Mn Alloys

Understanding effect of Mg and Mn equivalents on columnar-to-equiaxed transition of high-strength Al alloy fabricated by laser powder bed fusion

Effect of Microalloyed Al and Ca on Mechanical Properties and Corrosion Resistance of High-Speed Extruded Mg-2Zn-1Mn (mass%) Alloy

Effect of Sm content on microstructure and properties of extruded Mg-6Al-2Sr alloy

Effects of Al Concentration on Microstructure and Mechanical Properties of Mg-xAl-1Zn-1Si Alloy

Effects of Mn Addition on the Microstructures and Mechanical Properties of the Mg-15Gd-1Zn Alloy