Abstract:Magnesium‐lithium (MgLi) alloys have been widely used in various engineering fields due to their ultra-light characteristics. The strengthening of MgLi alloys is one of the key factors determining its application and has received extensive attention. In this work, the as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY (x = 0, 0.5 and 1.0, wt%) alloys with a density of only 1.52 g/cm3 were prepared via vacuum induction melting. The effects of rare earth element yttrium (Y) on the microstructure and mechanical properties of the MgLi alloy system were investigated. The results indicated that the microstructures of all the alloys mainly consisted of α-Mg, β-Li, AlLi, and MgLi2Al phases. The spherical AlLi phase was distributed inside the α-Mg and β-Li matrix. Part of the petal-like MgLi2Al phase was distributed in the interior of β-Li, and the rest grew along the grain boundaries as long strips. With the addition of Y, Al2Y phase formed with sharp edges and regular shapes. The Al2Y phase was mainly distributed inside the α-Mg phase and along the grain boundaries. Meanwhile, the amount of AlLi phase inside the α-Mg phase gradually decreased. The presence of nano-scale lath-shape MgLiZn phase in the β-Li matrix was observed in the HAADF map of the 0.5Y alloy. The continuous growth of MgLi2Al phase at the grain boundaries weakened its strength. As a consequence, it eventually led to intergranular fracture of the alloy. The 0.5Y alloy showed the highest tensile strength, up to ~244 MPa, and the yield strength was 60.5% higher than that of the 0Y alloy. Solid solution strengthening, precipitate strengthening and grain refinement were thus considered as the primary strengthening mechanisms caused by the addition of Y into the Mg-10Li-3Al-3Zn alloy.

Microstructures and mechanical properties of as-extruded Mg–5Sn–1Zn–xAl (x=1, 3 and 5) alloys

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructures and Mechanical Properties of a High-Strength Mg-3.5Sm-0.6Zn-0.5Zr Alloy

Effect of Zn Concentration on the Microstructures and Mechanical Properties of Extruded Mg–7Y–4Gd–0.4Zr Alloys

Investigation on corrosion behavior and mechanical properties of an extruded Mg-Zn-Al-Sn-Mn alloy

Effect of Ca addition on microstructure and mechanical properties of Mg–3.8Al–1.1Sn alloys

Microstructures and Mechanical Properties of As-Cast Mg–5Al–0.4Mn–xNd (x = 0, 1, 2 and 4) Alloys

Effect of Al on the Microstructure and Mechanical Properties of Mg–Sn–Ca–Mn Wrought Alloy

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

Microstructure and mechanical properties of as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY alloy with multi-precipitates

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

Microstructure, Non-Basal Texture and Strength-Ductility of Extruded Mg-6Bi-3Zn Alloy

Effect of Sn content on microstructure and tensile properties of as-cast and as-extruded Mg−8Li−3Al−(1,2,3)Sn alloys

Microstructure and mechanical properties synergistically enhanced via heat treatment modification of the as-extruded Mg-1.5Al-0.5Zn-0.2Y-0.2Ca alloy

Microstructure and Mechanical Properties of Extruded Mg-Zn-Nd-Y-Zr-Ca Alloy

Unveiling the microstructure evolution and deformation mechanisms of micro-alloying Mg-1.5Zn-0.5Zr-0.5Sr alloy via extrusion-shearing

Microstructure, Tensile Properties and Work Hardening Behavior of an Extruded Mg–Zn–Ca–Mn Magnesium Alloy

Effect of Zn content on microstructure, mechanical properties and thermal conductivity of extruded Mg-Zn-Ca-Mn alloys

Microstructures and Mechanical Properties of the Mg–4.5Zn–xGd (x = 0, 2, 3 and 5) Alloys

Effects of Zn Addition on the Microstructure, Tensile Properties and Formability of As-Extruded Mg-1Sn-0.5Ca Alloy