Abstract:In this study the effect of the cutting speed and an instantaneous heating source directly before cutting tool on the cutting force, cutting zones temperatures chip morphology, shear plane angle and strain rate during dry machining of Ti6Al4V. A 2D numerical model simulating orthogonal cutting process is created using Abaqus/Explicit software. In this model, Johnson Cook constitutive model is used to describe the material behavior during cutting process. Also, Johnson Cook damage model is used to simulation chip separation mechanism. After the verification of the model by comparison with results found in the literature, a number of simulations were run at different levels of four factors: cutting speed (40, 60, 80, 100, 120 and140m/min), heat source temperature (200, 400 and 600°C), heating source distance from the cutting tool (0.3, 0.6 and 0.9mm) and heating source size/diameter (0.6, 0.8 and 1mm). Taguchi L18 orthogonal mixed level design is used to plan for simulation runs using Minitab software. ANOVA analysis is used to investigate the significance of the four factors. The response table of means and the main effect of means is used to compare between the four factors and find their ranking. Based on 95% confidence Interval (CI), the results show that cutting speed has a significant effect on cutting force, strain rate, chip compression ratio, cutting tool nose temperature, cutting tool and chip temperature in the secondary deformation zone, average chip thickness at peaks and average chip thickness at valleys and average pitch. This conclusion is based on the P-values which are << 0.05 and the contribution which reaches 99.01%. Similarly, based on P-values < 0.05 and relatively high contribution reaches 12.16%, the heating source temperature has a significant effect on average chip thickness at valleys, chip compression ratio and strain rate. The cutting speed has Rank 1 among the four factors affecting cutting force, cutting zones temperatures, chip morphology, shear plane angel and stain rate. The effect of instantaneous heating directly before cutting process is negligible compared to the effect of plastic deformation and fracture mechanism in the cutting zone.

The Influences of Tool Wear on Ti6Al4V Cutting Temperature and Burn Defect

Tailorable Burning Behavior of Ti14 Alloy by Controlling Semi-Solid Forging Temperature

Investigation on Generation and Features of Burn Defect in Ti6al4v Milling

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Effects of Tool Flank Wear on Orthogonal Cutting Process of Aluminum Alloy

Inlfuences of Material Tool and Tool Wear on Cutting Temperature of Turning Titanium Matrix Composites

Study on the Effect of Tool Inclination Angle in Machining Process Based on Three-Dimensional Thermo-Elastic-Plastic Model

Investigation of Serrated Chip Morphology Change Regular in the Burning of Titanium Alloys

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

A Novel Finite Element Model for Thermally Induced Machining of Ti6Al4V

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Investigation of heat partition and instantaneous temperature in milling of Ti-6Al-4V alloy

Numerical Investigation on the Effect of Cutting-Edge Shape Factor on the Cutting Performance of Titanium Alloy

Cutting Performance of TiN/TiSiN Coated Tool during Turning of Ti6Al4V Titanium Alloy

Analysis of tool wear of TiAlN coated tool, machined surface morphology and chip during titanium alloy milling

Numerical Simulation of Combustion Resistant Titanium Alloy Wear Behavior at High Temperature Fields

Analysis of High Temperature Wear Process Mechanism of Cemented Carbide Tool

Simulation and Experimental Analysis of Tool Wear and Surface Roughness in Laser Assisted Machining of Titanium Alloy

Pressure-Induced Critical Influences on Workpiece-Tool Thermal Interaction in High Speed Dry Machining of Titanium

Finite Element Simulation of Orthogonal Cutting of H13-Hardened Steel to Evaluate the Influence of Coatings on Cutting Temperature

Subroutine Embedding and Finite Element Simulation of the Improved Constitutive Equation for Ti6Al4V during High-Speed Machining