Abstract:Thin-walled parts are often used in various industrial applications and due to their functional requirements, higher accuracies are generally desired. But due to their low stiffness characteristics, deformation and chatter problems are frequently encountered in their machining, thus resulting in poor accuracy. Moreover, due to 5-axes milling, which is usually required for finish machining of such parts, further complexities in the process are added and, consequently, achieving higher accuracy becomes more challenging. Therefore, in this study, the influence of tool inclination angle and feeding direction has been investigated on the resultant surface accuracy of thin cantilever shaped parts in finish milling conditions through experiments, finite element method simulations and theoretical discussions. Moreover, since work material’s microstructure and hardness also have key influence on its machinability, therefore, the effect of heat treatment state on resulting surface accuracy also has been explored. Three different titanium alloy, Ti–6Al–4 V specimens have been used. Two of the specimens were given solution treatment at 1050 ℃/1 h followed by aging at 550 ℃/4 h. One of the specimens after being solution treated was allowed to cool in air while the other was cooled in water to obtain different microstructure and hardness whereas the third specimen was used in as-received condition (casted). The three Ti–6Al–4 V specimens were machined at five different tool inclination angles (60°, 70°, 75°, 80°, and 85°) with two feeding directions (horizontal inwards and vertical inwards). Results have shown that the angle near the perpendicular to the surface i.e. 85° (5° away from the perpendicular) has lowest deformation value and also has better surface quality, which shows that the lowest effective cutting speed at this angle has helped in achieving higher accuracy. Moreover, among the cutting directions studied, vertical inward direction produces smoother surface due to its less pushing effect on the surface being cut as compared to horizontal inwards direction. And in terms of heat treatment state, the specimen which was cooled in air after being solution treated has produced better results for all cutting conditions studied, mainly attributed to fine homogenous lamellar α + β Ti–6Al–4 V structure achieved due to slow cooling rate of air. Analysis of variance using response surface methodology has been carried out to develop predictive model and to study the influence of each variable on the accuracy. The developed model has shown good accuracy when validated through additional experiments.

Investigation of heat partition and instantaneous temperature in milling of Ti-6Al-4V alloy

Research on 3D Numerical Simulation and Experiment of Cutting Temperature for High Speed Milling of Aerospace Aluminum Alloy

Experimental Studies of Cutting Temperature During High-Speed Milling of Aerospace Aluminum

Three-dimensional numerical simulation for high speed milling of aerospace aluminum alloy

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Study on the Effect of Tool Inclination Angle in Machining Process Based on Three-Dimensional Thermo-Elastic-Plastic Model

The heat partition into cutting tool at tool-chip contact interface during cutting process: a review

Simulation of High-Speed Milling Process of Aerospace Aluminum Alloy

Finite Element Simulation and Analysis of Aluminum Alloy Three-Dimensional Milling

A Novel Finite Element Model for Thermally Induced Machining of Ti6Al4V

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Development of a tool-workpiece thermocouple system for comparative study of the cutting temperature when high-speed ultrasonic vibration cutting Ti-6Al-4V alloys with and without cutting fluids

Modeling and Monitoring of the Tool Temperature During Continuous and Interrupted Turning with Cutting Fluid

Thermocouple and Infrared Sensor-Based Measurement of Temperature Distribution in Metal Cutting

Transient Temperature at Tool–Chip Interface during Initial Period of Chip Formation in Orthogonal Cutting of Inconel 718

Temperature modeling analysis for milling of titanium alloy

Influence of Tool Inclination Angle and Cutting Direction on Long Thin-Walled Part’s Dimensional and Geometric Accuracy when High-Speed Ball End Milling the Heat-Treated Titanium Alloy Ti–6Al–4 V

A Method for Thermal Performance Modeling and Simulation of Machine Tools

Investigation on cutting forces and tool wear in high-speed milling of Ti-6Al-4V assisted by longitudinal torsional ultrasonic vibrations

Numerical investigation on serrated chip formation during high-speed milling of Ti-6Al-4V alloy

A study on the thermodynamic characteristics of a mechanical A/C swing angle milling head