Abstract:All-polymer solar cells (all-PSCs) have attracted significant attention due to their unique advantages, such as intrinsic stretchability and high thermal stability. However, in the PM6:PYIT system, the control of phase-separated aggregation size of the acceptor PYIT is particularly crucial because of the difficulties in choosing the suitable solvents. High-boiling-point solvents such as chlorobenzene may lead to excessive aggregation of the acceptor due to the slow solvent evaporation and, the low-boiling-point solvents like chloroform (CF) may result in small aggregation sizes of the acceptor due to its fast evaporation. To optimize the aggregation size of the acceptor PYIT, we employ a strategy of using two high-boiling-point solvent additives (diphenyl ether: DPE and chloronaphthalene: CN) to prolong the aggregation and film formation time of the acceptor PYIT. The result shows that the aggregation state of PYIT was optimized effectively after the evaporation of CF, by the slow evaporation process of DPE and CN acts synergistically. Moreover, DPE with lower surface energy tends to make PM6 aggregate more in the bottom anode region, while CN with higher surface energy drives PYIT to aggregate upwards, forming a vertical phase separation distribution structure, which is conducive to efficient exciton dissociation and charge transport. Further analysis indicates that the introduction of the dual-additive leads to a corresponding increase in the external quantum efficiency (EQE) spectrum and an effective reduction in the absorption bandgap (Eg) of the solar cells. Consequently, the PCE of the optimized device increases notably, from 14.58% to 16.67% and a reduction in Eloss from 0.500 eV to 0.476 eV by adding 0.6 vol% of 1-CN and 0.4 vol% of DPE simultaneously.

Binary Additives Synergistically Boost the Efficiency of All-Polymer Solar Cells Up to 3.45%

Performance improvement of polymer solar cells with binary additives induced morphology optimization and interface modification simultaneously

To enhance the molecular aggregation and decrease the optical gap by the dual-additive to reduce the energy loss of all-polymer organic solar cells

Binary Additive–Induced Performance Improvement of PM7:PC71BM Organic Solar Cells with High Open‐Circuit Voltage and Enhanced Current Intensity

Improving Cooperative Interactions Between Halogenated Aromatic Additives and Aromatic Side Chain Acceptors for Realizing 19.22% Efficiency Polymer Solar Cells

Developing an efficient thiophene additive for 18.53% efficiency of binary polymer solar cells by adopting asymmetric strategy

Asymmetrified Benzothiadiazole-Based Solid Additives Enable All-Polymer Solar Cells with Efficiency Over 19

Optimizing Double‐Fibril Network Morphology via Solid Additive Strategy Enables Binary All‐Polymer Solar Cells with 19.50% Efficiency

Multifunctional Solid Additive Enabling All-Polymer Solar Cells with Improved Efficiency, Photostability and Mechanical Durability

Integrated Omnidirectional Design of Non‐volatile Solid Additive Enables Binary Organic Solar Cells with Efficiency Exceeding 19.5%

Binary All‐polymer Solar Cells with a Perhalogenated‐Thiophene‐Based Solid Additive Surpass 18% Efficiency

High performance all-polymer solar cells enabled with solvent and solid dual additives

Binary Additive–Induced Performance Improvement of PM7:PC 71 BM Organic Solar Cells with High Open‐Circuit Voltage and Enhanced Current Intensity

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

The effect of additive on the performance and phase separation of benzo[1,2-b:3,4-b′]dithiophene-based polymer heterojunction photovoltaic devices

High‐Efficiency (16.93%) Pseudo‐Planar Heterojunction Organic Solar Cells Enabled by Binary Additives Strategy

Synergistically optimizing the optoelectronic properties and morphology using a photo-active solid additive for high-performance binary organic photovoltaics

Additive-induced intermolecular interaction enhancement enables highly efficient organic solar cells

Non-halogenated and non-volatile solid additive for improving the efficiency and stability of organic solar cells

Improved Molecular Ordering in a Ternary Blend Enables All‐Polymer Solar Cells over 18% Efficiency

Isomeric Solid Additive Enables High‐Efficiency Polymer Solar Cells Developed Using a Benzo‐difuran‐based Donor Polymer