Abstract:All-polymer solar cells (all-PSCs) have attracted significant attention due to their unique advantages, such as intrinsic stretchability and high thermal stability. However, in the PM6:PYIT system, the control of phase-separated aggregation size of the acceptor PYIT is particularly crucial because of the difficulties in choosing the suitable solvents. High-boiling-point solvents such as chlorobenzene may lead to excessive aggregation of the acceptor due to the slow solvent evaporation and, the low-boiling-point solvents like chloroform (CF) may result in small aggregation sizes of the acceptor due to its fast evaporation. To optimize the aggregation size of the acceptor PYIT, we employ a strategy of using two high-boiling-point solvent additives (diphenyl ether: DPE and chloronaphthalene: CN) to prolong the aggregation and film formation time of the acceptor PYIT. The result shows that the aggregation state of PYIT was optimized effectively after the evaporation of CF, by the slow evaporation process of DPE and CN acts synergistically. Moreover, DPE with lower surface energy tends to make PM6 aggregate more in the bottom anode region, while CN with higher surface energy drives PYIT to aggregate upwards, forming a vertical phase separation distribution structure, which is conducive to efficient exciton dissociation and charge transport. Further analysis indicates that the introduction of the dual-additive leads to a corresponding increase in the external quantum efficiency (EQE) spectrum and an effective reduction in the absorption bandgap (Eg) of the solar cells. Consequently, the PCE of the optimized device increases notably, from 14.58% to 16.67% and a reduction in Eloss from 0.500 eV to 0.476 eV by adding 0.6 vol% of 1-CN and 0.4 vol% of DPE simultaneously.

Asymmetrified Benzothiadiazole-Based Solid Additives Enable All-Polymer Solar Cells with Efficiency Over 19

Binary All‐polymer Solar Cells with a Perhalogenated‐Thiophene‐Based Solid Additive Surpass 18% Efficiency

Fine Tuning Miscibility of Donor/Acceptor through Solid Additives Enables All‐Polymer Solar Cells with 15.6% Efficiency

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

High performance all-polymer solar cells enabled with solvent and solid dual additives

Multifunctional Solid Additive Enabling All-Polymer Solar Cells with Improved Efficiency, Photostability and Mechanical Durability

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

To enhance the molecular aggregation and decrease the optical gap by the dual-additive to reduce the energy loss of all-polymer organic solar cells

Isomeric Solid Additive Enables High‐Efficiency Polymer Solar Cells Developed Using a Benzo‐difuran‐based Donor Polymer

Improved Molecular Ordering in a Ternary Blend Enables All‐Polymer Solar Cells over 18% Efficiency

Approaching 19% Efficiency and Stable Binary Polymer Solar Cells Enabled by a Solidification Strategy of Solvent Additive

Enhancing the Performance of Polymer Solar Cells by Using Donor Polymers Carrying Discretely Distributed Side Chains.

Improving Performance of All‐Polymer Solar Cells Through Backbone Engineering of Both Donors and Acceptors

Improved Morphology and Efficiency of Polymer Solar Cells by Processing Donor–Acceptor Copolymer Additives

Fine Optimization of Morphology Evolution Kinetics with Binary Additives for Efficient Non-Fullerene Organic Solar Cells

Designed Polymer Donors to Match an Amorphous Polymer Acceptor in All-Polymer Solar Cells

Terpolymer Strategy Toward High-Efficiency Polymer Solar Cells: Integrating Symmetric Benzodithiophene and Asymmetrical Thieno[2,3-f]benzofuran Segments

Nonfullerene Acceptors with Enhanced Solubility and Ordered Packing for High-Efficiency Polymer Solar Cells

Developing Y‐Branched Polymer Acceptor with 3D Architecture to Reconcile Between Crystallinity and Miscibility Yielding >15% Efficient All‐Polymer Solar Cells

Asymmetric Isomer Effects in Benzo[ c ][1,2,5]thiadiazole‐Fused Nonacyclic Acceptors: Dielectric Constant and Molecular Crystallinity Control for Significant Photovoltaic Performance Enhancement

Optimizing Double‐Fibril Network Morphology via Solid Additive Strategy Enables Binary All‐Polymer Solar Cells with 19.50% Efficiency