Abstract:In this work, a novel halogen‐free and twisted volatile solid additive 1,4‐diphenoxybenzene (DPB) has been employed to control the morphology of the active layer in organic solar cells (OSCs). As a result, a champion power conversion efficiency (PCE) of 19.04% has been obtained in D18‐Cl:N3 binary OSCs, which is the highest value for the reported D18‐Cl:N3 OSCs to date. Recently, volatile solid additives have attracted tremendous interest in the field of organic solar cells (OSCs), which can effectively improve device efficiency without sacrificing the reproducibility and stability of the device. However, the structure of reported solid additives is onefold and its working mechanism needs to be further investigated. Herein, a novel non‐halogenated and twisted solid additive 1,4‐diphenoxybenzene (DPB) is employed to optimize the morphology of the active layer in OSCs. The properties of additive DPB, morphology of active layer, and carrier dynamics behaviors have been systematically investigated through theoretical calculations, in situ and ex situ spectroscopy, grazing‐incidence wide‐angle X‐ray scattering (GIWAXS), and grazing‐incidence small‐angle X‐ray scattering (GISAXS) measurement, as well as ultrafast spectroscopy technology. The results reveal that the twisted additive DPB selectively interacts with acceptor Y6, and thus forms optimized morphology of active layer with increased molecular crystallinity, tight molecular packing, and favorable phase separation. As a result, the optimized devices deliver a remarkable power conversion efficiency (PCE) of 19.04%, which is the highest value for the D18‐Cl:N3 system to date. These results demonstrate that non‐halogenated and twisted solid additive DPB has broad prospects in the preparation of highly efficient OSCs, providing theoretical and experimental guidance for the development of high‐performance solid additives.

Binary Additive–Induced Performance Improvement of PM7:PC 71 BM Organic Solar Cells with High Open‐Circuit Voltage and Enhanced Current Intensity

Binary Additive–Induced Performance Improvement of PM7:PC71BM Organic Solar Cells with High Open‐Circuit Voltage and Enhanced Current Intensity

Simultaneously Enhancing Exciton/Charge Transport in Organic Solar Cells by an Organoboron Additive

High‐Efficiency (16.93%) Pseudo‐Planar Heterojunction Organic Solar Cells Enabled by Binary Additives Strategy

Performance improvement of polymer solar cells with binary additives induced morphology optimization and interface modification simultaneously

Novel Brominated Compounds Using in Binary Additives Based Organic Solar Cells to Achieve High Efficiency over 10.3%

Solid Additive‐Assisted Selective Optimization Strategy for Sequential Deposited Active Layers to Construct 19.16% Efficiency Binary Organic Solar Cells

Synergistic Effects of Solid and Solvent Additives on Film Morphology Enable Binary Organic Solar Cells with Efficiency of Over 19%

16.7%-efficiency ternary blended organic photovoltaic cells with PCBM as the acceptor additive to increase the open-circuit voltage and phase purity

The Influence of Binary Processing Additives on the Performance of Polymer Solar Cells

Subtle Morphology Control with Binary Additives for High Efficiency Non-Fullerene Acceptor Organic Solar Cells.

19.0% Efficiency Binary Organic Solar Cells Enabled by Using a Building Block As Solid Additive

Integrated Omnidirectional Design of Non‐volatile Solid Additive Enables Binary Organic Solar Cells with Efficiency Exceeding 19.5%

Additive-induced intermolecular interaction enhancement enables highly efficient organic solar cells

A Broad-Spectrum Solid Additive to Further Boost High-Efficiency Organic Solar Cells via Morphology Regulation

Simultaneously Enhancing Exciton/Charge Transport in Organic Solar Cells by Organoboron Additive

Developing an efficient thiophene additive for 18.53% efficiency of binary polymer solar cells by adopting asymmetric strategy

Morphology Optimization by Non‐Halogenated and Twisted Volatile Solid Additive for High‐Efficiency Organic Solar Cells

Hydrogen-Bonding Strategy to Optimize Charge Distribution of PC71BM and Enable a High Efficiency of 12.45% for Organic Solar Cells

Achieving high-performance ternary organic solar cells by adding a high hole-mobility non-fullerene acceptor

Synergistic Effect of Solvent and Solid Additives on Morphology Optimization for High-Performance Organic Solar Cells