Abstract:An easy isomerization strategy for additives enables more reasonable molecular spatial distribution and better π–π stacking behavior of bulk heterojunction, which provides guidance for screening and designing additives with excellent morphology improvement capability and is expected to have a profound influence on further increasing efficiency of organic solar cells without adopting the isomerization strategy for active molecules possessing complex conjugated backbones and branched chains. The morphological features of the active layer has always been an important factor limiting the efficiency of organic solar cells (OSCs). Although halogen‐based additives capable of forming non‐covalent bonds with active molecules can effectively adjust the morphology of active layer, the inner mechanism of positional isomerization of additives on the crystallization kinetics of bulk heterojunction has been ignored, which hinders further development of this technique. Herein, a new additive‐assisted optimization strategy for high‐efficiency OSCs based on three positional isomeric additives is proposed, which have different sites for two bromine substituents on the benzene ring. The results demonstrate that symmetrically structured additives with the smallest dipole moment, the lowest steric hindrance and the most uniformly distributed electrostatic potential, can form more suitable non‐covalent interactions with the acceptor, resulting in more reasonable molecular spatial distribution and better π–π stacking behavior. For other non‐fullerene systems, the symmetrically structured additive also shows the best effect on optimizing molecular aggregation and stacking. This work provides guidance for screening and designing additives with excellent morphology improvement capability and is expected to have a profound influence on further increasing efficiency of OSCs without adopting the isomerization strategy for active molecules possessing complex conjugated backbones and branched chains.

Revealing Morphology Evolution in Highly Efficient Bulk Heterojunction and Pseudo‐Planar Heterojunction Solar Cells by Additives Treatment

High‐Efficiency (16.93%) Pseudo‐Planar Heterojunction Organic Solar Cells Enabled by Binary Additives Strategy

Morphology Optimization by Non‐Halogenated and Twisted Volatile Solid Additive for High‐Efficiency Organic Solar Cells

Additive-induced intermolecular interaction enhancement enables highly efficient organic solar cells

19.10% Efficiency and 80.5% Fill Factor Layer‐by‐Layer Organic Solar Cells Realized by 4‐Bis(2‐thienyl)pyrrole‐2,5‐Dione Based Polymer Additives for Inducing Vertical Segregation Morphology

Dual Additive Strategy with Quasi-Planar Heterojunction Architecture Assisted in Morphology Optimization for High-Efficiency Organic Solar Cells

A Broad-Spectrum Solid Additive to Further Boost High-Efficiency Organic Solar Cells via Morphology Regulation

Synergistic Effect of Solvent and Solid Additives on Morphology Optimization for High-Performance Organic Solar Cells

Oligothiophene Additive‐Assisted Morphology Control and Recombination Suppression Enable High‐Performance Organic Solar Cells

Synergistic Control of Multilength-Scale Morphology and Vertical Phase Separation for High-Efficiency Organic Solar Cells

Miscibility Control by Tuning Electrostatic Interactions in Bulk Heterojunction for Efficient Organic Solar Cells

Easy Isomerization Strategy for Additives Enables High‐Efficiency Organic Solar Cells

Enhancing stability and performance of pseudo-planar heterojunction organic solar cells using a hindered phenolic antioxidant with over 19% efficiency

Volatilizable Solid Additive‐Assisted Treatment Enables Organic Solar Cells with Efficiency over 18.8% and Fill Factor Exceeding 80%

Unraveling the Effect of Solvent Additive and Fullerene Component on Morphological Control in Organic Solar Cells

Achieving Desired Pseudo‐Planar Heterojunction Organic Solar Cells via Binary‐Dilution Strategy

Polymer Solar Cells with 18.74% Efficiency: From Bulk Heterojunction to Interdigitated Bulk Heterojunction

2D/1a Strategy to Regulate Film Morphology for Efficient and Stable Nonfullerene Organic Solar Cells

Reducing Energy Loss and Morphology Optimization Manipulated by Molecular Geometry Engineering for Hetero‐junction Organic Solar Cells

Synchronous Regulation of Donor and Acceptor Microstructure using Thiophene‐Derived Non‐Halogenated Solvent Additives for Efficient and Stable Organic Solar Cells

Dual-Additive-Driven Morphology Optimization for Solvent-Annealing-Free All-Small-Molecule Organic Solar Cells