Abstract:Currently, porous SiC ceramics have been a focus of interesting research in the field of porous materials due to their excellent structural properties, high strength, high hardness, and superb mechanical and chemical stabilities even at high temperatures and hostile atmospheres. Porous SiC ceramics have been considered as suitable candidate materials for catalyst supports [1-2], hot gas or molten metal filters [3], high temperature membrane reactors [4], thermal insulating materials [5], gas sensors [6] etc. Porous SiC ceramics are fabricated by various methods including partial sintering [7], carbothermal reduction [8-9], replication or pyrolysis of polymeric sponge [10-12], reaction bonding [13] etc. In all these methods SiC needs to be sintered which requires a very high temperature due to the strong covalent nature of the Si-C bond, selective sintering additives, expensive atmosphere, costly and delicate instrumentation. Processing of porous SiC ceramics at low temperature using a simple technique thus becomes necessary. Bonding of SiC can be done at low temperatures by use of different oxide and non-oxide secondary phases. They include silica, mullite, cordierite, silicon nitride, etc. Various sintering additives are used for the formation of variety of secondary oxide bond phases for formations for porous SiC [14-19] Choice of mullite as a bond for SiC has many advantages. Mullite possesses a high melting point (T m = 1850°C) and a low oxygen diffusion coefficient (5.6 x 10 -14 m 2 /sec at 50°C). It has a matching thermal expansion coefficient with SiC (CTE mullite = 5.3 ×10 -6 /K; CTE SiC = 4.7 ×10 -6 /K at RT-1000 °C) and a high strength that can be retained up to a very high temperature. Different sources of aluminum, such as Al 2 O 3 , Al, AlN, and Al (OH) 3 powders were used for the formation of mullite bonded porous SiC ceramics (MBSC) [20-21]. However, the mullitization temperature of 1550 o C is still necessary. In this work, mullite bonded porous SiC ceramics were fabricated by an in situ reaction-bonding process; the mixture of clay and CaCO 3 were chosen as sintering additives to lower the mullitization reaction between Al 2 O 3 and oxidation-derived SiO 2. The effect amount of alumina, sintering temperature and other sintering aids on material property such as porosity/pore size distribution mechanical and micro structural properties of porous oxide bonded SiC ceramics were studied.

Preparation of High-Temperature Structural Mullite/sic-Si3n4 Multiphase Ceramics

The Effects of Mineral Composition and Sintering Temperature on Synthetic Mullite

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

A Simple and Efficient Way to Prepare Porous Mullite Matrix Ceramics Via Directly Sintering SiO2-Al2O3 Microspheres

Low-temperature Densification and Mechanical Properties of Monolithic Mullite Ceramic

Fabrication and Properties of SiC/mullite Composite Porous Ceramics

The Effect of Bond Phase Additive and Sintering Temperature on the Properties of Mullite Bonded Porous SiC Ceramics

Effect of Sic on Microstructures and Properties of Cordierite-Mullite Multiphase Ceramics Material

Preparation and properties of porous mullite-based ceramics fabricated by solid state reaction

Microstructures and Mechanical Properties of Pressureless Sintered Ca-3(PO4)(2)/Si3N4 Composite Ceramics

Effect of Silicon Addition on Mechanical Properties of Mullite-Sic Composite Refractories

The Fabrication of Porous Mullite Ceramics Based on the Different Sizes of Aluminum Hydroxide

Emulsion-templated High Porosity Mullite Ceramics with Sericite Induced Textured Structures

Physico-Mechanical and Microstructure Characteristics of Porous Mullite Ceramics

Preparation of Mullite Glass-ceramics from High Alumina Fly Ash: an Experimental Study

Low-temperature Synthesis of Highly Porous Whisker-Structured Mullite Ceramic from Kaolin

Preparation of Mullite-Aluminum Titanate-Cordierite Multiphase Ceramics

Fabrication of Si3N4 Ceramics with High Thermal Conductivity and Flexural Strength Via Novel Two-Step Gas-Pressure Sintering

Microstructures and Mechanical Properties of Mullite/SiC Composite Ceramics Prepared by Gelcasting

Study on Micro-structure and Properties of Al2O3/SiC Ceramics by Pressureless Sintering in Air

Densification, Microstructure and Mechanical Properties of Multicomponent (tizrhfnbtamo)c Ceramic Prepared by Pressureless Sintering