Abstract:<p>In this study, the microstructure evolution and mechanical anisotropy of the extruded Mg-2Zn-0.4Mn-0.4Ce alloy tube during tensile loading along the extrusion direction (ED), 45° towards extrusion direction (45°ED) and transverse direction (TD) were investigated, respectively. The results showed that the initial extruded alloy tube had an obvious {0001} basal fiber texture with the symmetrical pole position deviating about 20° from the RD to ED, which resulted in mechanical anisotropy of the tensile yield stress (TYS) when tensile loading along the ED, 45°ED and TD. The deformation behavior of the alloy tube consisted of three stages. In the yield process, the deformation was dominated by prismatic<a>slip under tensile loading along the ED, while the deformation was dominated by basal<a>slip, next were prismatic<a>slip and pyramidal<c+a>slip under tensile loading both along the 45°ED and TD. In the initial stage after yielding, some extension twin (ETW) formed when tensile loading along the three direction, and the deformations were still dominated by the previous slip systems. In the later part of the deformation, the activation of prismatic<a>slip and the nucleation and expansion of ETW gradually reached saturation under tensile loading along the ED. The dominated prismatic<a>slip was gradually replaced by pyramidal<c+a>slip, and accompanied with a small content of contraction twin (CTW) and double twin (DTW), thus forming a typical texture of [0001]⊥ED. For the deformation both along the 45°ED and TD, dominated prismatic<a>slip and subdominant pyramidal<c+a>slip gradually became the main deformation mode after the saturation of basal<a>slip and ETW, and a small content of CTW and DTW also formed, thus forming the texture of [0001]∥ED-RD plane.</a></c+a></a></c+a></a></a></c+a></a></a></a></p>

Microstructure and Mechanical Behavior of the Mg–Mn–Ce Magnesium Alloy Sheets

Investigation on microstructures and mechanical properties of Mg–6Zn–0.5Ce–xMn (x = 0 and 1) wrought magnesium alloys

Effect of Ce Addition on the Microstructure, Thermal Conductivity and Mechanical Properties of Mg–0.5Mn Alloys

The microstructure evolution and mechanical anisotropy of extruded Mg-2Zn-0.4Ce-0.4Mn alloy tube during tension in different directions

Effect of cerium alloying on microstructure, texture and mechanical properties of magnesium during cold-rolling process

Enhanced Strength-Ductility Synergy in Mg-0.5 wt%Ce Alloy by hot Extrusion

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Effect of Sm and Ce content on microstructure and mechanical property of newly developed Mg-Sm-Ce-Mn based alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Influence of Ce content on the microstructures and tensile properties of Mg-1Gd-0.5Zn alloys

Mechanical properties of Mg-Ce-Y-Zr-Zn-Ca microalloyed magnesium alloys composed of near-atomic solute

Microstructural characterization and mechanical behavior of Mg-AZ31B/Al 6063 bimetallic sheets produced by combining continuous shear deformation with direct extrusion

A novel continues multi-shear extrusion process on the microstructure and mechanical property evolution of AZ31 magnesium alloys

Microstructure Characterization and Mechanical Properties of a Zn and Rare Earth Modified Mg Alloy

Mechanical Properties and Deformation Mechanism of Mg-Al-Zn Alloy with Gradient Microstructure in Grain Size and Orientation

Towards reducing tension-compression yield and cyclic asymmetry in pure magnesium and magnesium-aluminum alloy with cerium addition

Multiscale Mechanical Behavior and Microstructure Evolution of Extruded Magnesium Alloy Sheets: Experimental and Crystal Plasticity Analysis

The improvement of grain refinement, texture modification and mechanical properties of pure Mg prepared by cyclic expansion extrusion with an asymmetric extrusion cavity

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

Microstructure evolution and mechanical property of Mg-3Al alloys with addition of Ca and Gd during rolling and annealing process

Microstructure and corrosion properties of Mg–0.5Zn–0.2Ca–0.2Ce alloy with different processing conditions