Towards reducing tension-compression yield and cyclic asymmetry in pure magnesium and magnesium-aluminum alloy with cerium addition

Shubham Sisodia,Jananandhan S,Vamsi Krishna Pakki,Chethan Konkati,Ankur Chauhan

DOI: https://doi.org/10.1016/j.msea.2023.145672

2023-09-19

Abstract:In this study, we report the effect of cerium (Ce) addition on the tension-compression yield and cyclic asymmetry in commercially pure magnesium (Cp-Mg) and Mg-Al alloy at room temperature (RT). The investigated materials Cp-Mg, Mg-0.5Ce, and Mg-3Al-0.5Ce were extruded at 400°C, followed by annealing at the same temperature for one hour. Incorporating 0.5wt.% Ce in pure Mg results in the weakening of its basal texture, uniform distribution of Mg12Ce precipitates, and grain size refinement. Consequently, the tensile yield strength and ductility of pure Mg increased, and tension-compression yield asymmetry was eliminated. However, the presence of 3wt.% Al in Mg suppresses the beneficial effects of Ce addition. The formation of complex precipitates, such as Mg-Al-Ce and Al11Ce3, limits the weakening of the basal texture, reduction in grain size, improvement in ductility, and elimination of tension-compression yield asymmetry observed in Mg-0.5Ce. Nevertheless, Al contributes to the solid solution strengthening in Mg and possibly lowers the critical stress required for twinning in Mg, resulting in the highest tensile strength of Mg-3Al-0.5Ce. Finally, the addition of 0.5wt.% Ce enhances the cyclic strength, stabilizes cyclic stress response, reduces inelastic strain, and minimizes cyclic asymmetry in both pure Mg and Mg-Al alloy while maintaining a comparable fatigue life. Overall, Ce addition positively impacts the microstructure and mechanical behavior of pure Mg and its investigated alloy. The reasons for these improvements are discussed in detail.

Materials Science

What problem does this paper attempt to address?

The paper aims to study the effect of cerium (Ce) addition on the tensile-compression yield behavior and cyclic asymmetry of pure magnesium (Cp-Mg) and magnesium-aluminum alloys at room temperature. Specifically, the study observes the impact of adding 0.5wt.% cerium on the material's microstructure, tensile properties, compressive properties, and low-cycle fatigue response. The main findings are as follows:

1. **Microstructure Changes**:
- After adding cerium, the basal texture of pure magnesium is weakened, Mg12Ce precipitates are uniformly distributed, and the grain size is refined.
- In the magnesium-aluminum alloy, the presence of aluminum inhibits the beneficial effects of cerium, resulting in less pronounced weakening of the basal texture and grain refinement compared to pure magnesium.

2. **Improvement in Mechanical Properties**:
- After adding cerium, both the tensile strength and plasticity of pure magnesium are improved, with the tensile yield strength increasing by approximately 2.15 times and the ultimate tensile strength increasing by approximately 1.28 times.
- The aluminum-containing magnesium alloy (Mg-3Al-0.5Ce) also shows higher yield strength, but its plasticity is slightly lower than that of the aluminum-free magnesium alloy (Mg-0.5Ce).

3. **Elimination of Tensile-Compression Asymmetry**:
- Pure magnesium exhibits significant tensile-compression asymmetry, which is eliminated after adding cerium.
- The tensile-compression asymmetry of the magnesium-aluminum alloy (Mg-3Al-0.5Ce) is reduced but still present.

4. **Enhanced Low-Cycle Fatigue Response**:
- Adding cerium can improve cyclic strength, stabilize cyclic stress response, reduce inelastic strain, and minimize cyclic asymmetry while maintaining considerable fatigue life.

Overall, the addition of cerium significantly improves the microstructure and mechanical properties of pure magnesium and its alloys, particularly in terms of tensile-compression asymmetry and low-cycle fatigue. The reasons for these improvements are discussed in detail in the paper.