Abstract:Blending type of ABS with different polybutadiene rubber (PB) and polyacrylonitrile (AN) contents in SAN phase is prepared at 240 degrees C to study the effects of PB and AN content on the structure and the properties of DB/ABS blends. Different kinds of productive ABS along with the blend-type ABS are used to compare the properties of PC/ABS and DB/ABS blends comprehensively. All blends are made by melt blending for 10 min with sheer rate of 30 r/min. The result shows that, in DB/Blend-type ABS (70/30) blends, PB content exhibits significant influence on the tensile properties. Samples with 6.3 wt% of PB always show the best performance both in yield strength and elongation at break when AN content is fixed at 18 wt%, 25 wt% and 30 wt%; while increasing AN content in the sample with the same PB content would result in better blends properties even not so obvious as PB content. Scanning electron microscopy gives exactly the same trend for phase morphology with PB and AN contents, revealing best uniform scale of dispersed phase (ABS) among 0.5 - 1.2 mu m at 6.3 wt% of PB. Thermal gravimetric analysis shows that all DB/ABS blends have good thermal stability, which is not obviously affected by PB content and AN content. Single peak of glass transition shows good compatibility in the DB/ABS blends. Excellent compatibility of DB with ABS in the sample is exhibited through dynamic mechanical analysis. The glasstransition temperature of DB/ABS blends are closed to that of DB, mildly affected by PB and AN content. Besides, both blending type ABS and different kinds of productive type ABS are used to compare the properties of DB/ABS blends and traditional bisphenol-A-type PC/ABS blends. Basic laws of tensile properties in DB/ABS remain the same as in PC/ABS blends using different types of ABS.

Study on the Structure and Properties of ABS/PA6/SMA Blends

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

MORPHOLOGY AND MECHANICAL PROPERTIES OF NYLON-6/ABS POLYMER BLENDS COMPATIBILIZED BY STYRENE-MALEIC ANHYDIDE COPOLYMER

Creating Super-Tough and Strong PA6/ABS Blends Using Multi-Phase Compatibilizers

Effect of Maleic Anhydride Copolymerization Mode on the Properties of PA6/ABS Blends

Compatibilization of Polyamide 6/Poly(2,6-Dimethyl-1,4-phenylene Oxide) Blends by Poly( Styrene-Co-Maleic Anhydride)

The Effect of Blending Sequence on Phase Morphology of Nylon 6/abs/sma Blends

Morphology and Mechanical Properties of Nylon 6/PBT Blends Compatibilized with Styrene/Maleic Anhydride Copolymer

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Effect of poly(styrene-co-maleic anhydride) on physical properties and crystalline behavior of nylon-6/PEBA blends

Blending ABS resin and its effect on structure and properties of PC/ABS BLEND alloy

The Preparation of Mah/St Multi-Monomer Melt Grafting on Abs and Its Compatibilizer Effect on Pa6/Abs Blends

Joint Effect of Compatibilizer and Organo-Montmorillonite on Compatibilization of Polyamide-6/Poly(Phenylene Oxide) Blend: Morphology and Properties

Preparation of Amine-Functionalized Compatilizer for PC/ABS Blends

Study on the Microstructures and Mechanical Behaviour of Compatibilized Polypropylene/Polyamide-6 Blends

Effect of ABS types on the morphology and mechanical properties of PA6/ABS blends by in situ reactive extrusion

Repurposing ABS to Produce Polyamide 6 (PA6)-Based Blends: Reactive Compatibilization with SAN-g-MA of a High Degree of Functionalization

Structure and Properties of Isosorbide type Polycarbonate/ABS Blend

Polyamide 66/poly(2,6-dimethyl-1,4-phenylene oxide) compatibilization with styrene–acrylonitrile–glycidyl methacrylate: rheology, morphology, and mechanical properties

Fatigue resistance and failure behavior of reaction compatibilized PC/ABS blends under tensile cyclic loading