Effects of Ar/H-2 Annealing on the Microstructure and Magnetic Properties of Coo Nanoparticles

Xuemin He,Zhiwen Li,Xing Zhang,Wen Qiao,Xueyin Song,Shiming Yan,Wei Zhong,Youwei Du

DOI: https://doi.org/10.1039/c5ra09723a

IF: 4.036

2015-01-01

RSC Advances

Abstract:Hysteresis loops and ZFC/FC curves of the Co/CoO composite nanoparticles.

What problem does this paper attempt to address?

Effect of Second Annealing on Magnetic Properties and Microstructure of (nddy)fecocub Magnets

W Wang,W Luo,YH Wen,LQ Yu,M Yan

DOI: https://doi.org/10.3321/j.issn:1002-185x.2005.10.030

2005-01-01

Abstract:The effect of a second annealing technique on the magnetic properties and microstructure of Nd12.0Dy2.8Fe74.7Co3.4Cu0.2B6.9 magnets have been investigated. The results show that the second annealing technique has little effect on residual magnetization and maximum energy product. Coercivity H-cj improves with the increase of annealing temperature, and the maximum can be achieved when annealed at 480 degrees C. Above 480 degrees C, H-cj decreases rapidly with the further increase of the second annealing temperature. When annealed at 480 degrees C, H-cj improves as increasing annealing time and the maximum H-cj can be achieved at 2h. Above 2h, the further increase of time has little effect on H-cj. SEM analysis shows that when annealed at 480 degrees C for 2h, the grain boundaries of the magnets are more smooth and the distribution of RE-rich phase in the grain boundaries is continuous and uniform.
Effect of Annealing on the Microstructure and Magnetic Properties of Fe-based Nanocomposite Materials

MH Phan,HX Peng,MR Wisnom,SC Yu,N Chau

DOI: https://doi.org/10.1016/j.compositesa.2005.01.033

IF: 9.463

2005-01-01

Composites Part A Applied Science and Manufacturing

Abstract:The influence of annealing on microstructure, magnetic properties including the giant magnetoimpedance (GMI) effect of a Fe-based nanocomposite has been investigated. The nanocomposite structure composed of ultra-fine Fe(Si) grains embedded in an amorphous matrix was attained by annealing the Fe-based amorphous alloy prepared by rapid quenching method. The GMI profiles were measured for samples annealed at different temperatures ranging from 350 to 650°C in vacuum and for 30min. It is found that the mean grain size of the α-Fe(Si) crystallites in the order of 12nm remains almost unchanged until the annealing temperature reached 540°C. A decrease of anisotropy field and an increase of GMI with increasing annealing temperature up to 540°C were observed and ascribed to the increase of the magnetic permeability and the decrease of the coercivity, whereas the opposite tendency was found for the sample annealed above 600°C which is likely due to the microstructural change caused by high-temperature annealing. This indicates that variation in the magnetic characteristic of the amorphous phase upon annealing changed the intergrain exchange coupling. This altered both the magnetic softness and the effective anisotropy and consequently modified the GMI features. The study of the temperature dependence of the GMI effect provides further understanding of the magnetic exchange between these crystallized grains through the amorphous boundaries in Fe-based nanocrystalline materials.
Annealing and composition dependence of magnetic properties of Co-C nanocomposite thin films

TANG Rui-he,WU Zhang-ben,YANG Zhi-gang,Chi Zhang,LIU Xiao-fang,Bai Yang,YU Rong-hai

2011-01-01

Abstract:Co-C nanocomposite thin films with Co contents of 13.0%-24.6 at% were deposited by magnetron sputtering. Co-C thin films were annealed at 400°C for 2h in vacuum. Magnetic hysteresis loops of the as-deposited and annealed samples were measured at 5, 77 and 300K. Annealing and composition dependence of microstructure and magnetic properties of Co-C nanocomposite thin films were investigated systematically. The as-deposited thin films show weak magnetization. Magnetic properties get enhanced after annealing. Samples with low Co content exhibit ferromagnetic properties at low temperature while superparamagnetic properties at room temperature, which is characteristic granular nature. Magnetization and coercivity, associated with the blocking temperature of Co-C thin films increase with increasing Co content.
Annealing Environment Effects on the Microstructure and Magnetic Properties of FePt–TiO2 and CoPt–TiO2 Nanocomposite Films

Rujun Tang,Wanli Zhang,Yanrong Li

DOI: https://doi.org/10.1016/j.jallcom.2010.02.018

IF: 6.2

2010-01-01

Journal of Alloys and Compounds

Abstract:The effects of Ar and Ar + 4%H2 annealing environments on the microstructure and magnetic properties of the FePt–TiO2 and CoPt–TiO2 nanocomposite films were investigated. Results showed that the annealing environments affect the phase transformations of L10-FePt and L10-CoPt alloys greatly. The Ar + 4%H2 significantly improved the L10-ordering of FePt–TiO2 and CoPt–TiO2 nanocomposites compared to the Ar. The CoPt–TiO2 nanocomposite exhibited better L10-ordering and larger coercivity than those of FePt–TiO2 due to the better oxidation resistance.
The Effect of Annealing on Microstructure and High Temperature Erosion Property of Arc-Spraying Coatings Containing Nanosized Ceramic Powders

LIU Shao-guang,WU Jin-ming,ZHANG Sheng-cai,RONG Shu-jie,HU Xiao-hai,LI Zhi-zhang

DOI: https://doi.org/10.3321/j.issn:1001-9731.2006.12.049

2006-01-01

Journal of Functional Biomaterials

Abstract:A composite coating containing nanosized ceramic powders was fabricated by a supersonic arc-spraying procedure using corresponding cored wires.The microstructure and high temperature erosion property of the coating were studied by characterizations with optical microscope,microhardness,X-ray diffraction,scanning electron microscopy and transmission electron microscopy,with special attentions paid to the effect of the subsequent annealing treatment.The results show that the skin and the cored powders melted and fused to form homogeneous solid solutions during the arc-spraying procedure using the cored wires.The achieved coating shows homogeneous hardness.The subsequent annealing of the coating reduced defects and residual stress,decomposed the metastable phases and at the same time improved the crystallinity of corresponding phases in the coating,which in turn improved its hardness.The high-temperature erosion resistance of the coatings after the subsequent annealing improved significantly.
Microstructure and phase dependence of magnetic properties of CoFeB nanowires

Zhe Chen,Kewei Zhang,Qianke Zhu,Qi Guo,Yong Jiang

DOI: https://doi.org/10.1016/j.vacuum.2020.109797

IF: 4

2021-01-01

Vacuum

Abstract:Arrays of amorphous CoFeB nanowires with the diameter of 250 nm and length of 20 μm were fabricated by electrodepositing in pores of anodic aluminum oxide (AAO) templates. The corresponding changes of coercivity (Hc), remanence squareness (Mr/Ms), and the shape of hysteresis loops of NWs before and after annealing with the microstructure evolution have been investigated. The XRD and TEM results showed the precipitation of partial Co nanocrystallites and complete crystallization for the annealing treatment at 573 K and 773 K, respectively. The VSM results indicated a strong magnetic anisotropy in the amorphous nanowires and the easy magnetization axis was in perpendicular to the long wire axis. Both Hc and Mr/Ms increased with increasing annealing temperature. The magnetization reversal process occurred by the curling model for the amorphous nanowires and exhibited a transition for magnetization reversal after thermal annealing. In all, the magnetic properties of CoFeB nanowires can be controlled by tuning their microstructure with thermal annealing.

materials science, multidisciplinary,physics, applied
Effect of Annealing on the High Co-doped Ti1-xCoxO2 Magnetic Semiconductor

Song Hong-Qiang,Wang Yong,Yan Shi-Shen,Mei Liang-Mo,Zhang Ze

DOI: https://doi.org/10.7498/aps.57.4534

2008-01-01

Abstract:High Co doping concentration Ti1-xCoxO2 magnetic semiconductor films were prepared by rf co-sputtering and then annealed for 2 hours at 200℃, 300℃ and 400℃ respectively. Microstructure and composition analysis by transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) indicated that the films were in the metastable state and the annealing has large effect on their microstructure, composition and magnetism.
Microstructure, magnetic and magnetotransport properties of Co-C nanocomposite thin films

Ruihe Tang,Zhigang Yang,Chi Zhang,Bai Yang,Xiaofang Liu,y u ronghai

DOI: https://doi.org/10.3724/SP.J.1037.2010.00546

2011-01-01

Abstract:Co-C nanocomposite thin films with a Co atomic content of 13.0% were fabricated onto Si (100) substrates by magnetron co-sputtering technique. Post annealing was carried out in vacuum at annealing temperature ranging from 473 K to 773 K for 30 min. TEM images indicate that the Co nanoparticles are dispersed uniformly in an amorphous carbon matrix for the as-deposited samples, and Co particle size is in a range of 1.5-3.0 nm. After annealing at 673 K, the average Co particle size is enlarged distinctly. Magnetization hysteresis loops reveal that the as-deposited thin films show low magnetization. As annealing temperature is increased, both magnetization and coercivity are enhanced significantly. The samples annealed at 673 K and 773 K show ferromagnetic behaviors at low temperature, and superparamagnetic behaviors at room temperature, which are characteristic magnetic features for granular system. A negative magnetoresistance (MR) of 1.33% is observed for the as-deposited Co-C thin films at 4.2 K in the applied magnetic field of 3980 kA/m. The MR value decreases with increasing annealing temperature. Resistance (R) versus temperature (T) curves exhibit a good linear relationship of lnR-T-1/4 at a broad low temperature range, suggesting that the conduction in Co-C nanocomposite thin films follows the variable range hopping transport mechanism. © Copyright.
Effects of Annealing on the Structure and Magnetic Properties of Fe27co23pb50 Nanowire Arrays

R. L. Wang,S. L. Tang,Y. G. Shi,X. L. Fei,B. Nie,Y. W. Du

DOI: https://doi.org/10.1063/1.2829898

IF: 2.877

2008-01-01

Journal of Applied Physics

Abstract:Ferromagnetic-nonmagnetic heterogeneous Fe27Co23Pb50 ternary metal nanowire arrays were successfully fabricated by alternating current electrodeposition into anodic alumina oxide (AAO) template. The effects of the different annealing temperatures (100, 200, 300, 400, 500, 600°C) on the structure and magnetic properties have been discussed. X-ray diffraction observations indicated that FeCo and Pb phases coexist for the as-deposited and annealed samples. Magnetic measurements indicate that the nanowire arrays have high perpendicular magnetic anisotropy with their easy axis parallel to the nanowire arrays. The coercivity and remanence ratio increases as the annealing temperature rises, reaches their maximum at 400°C, and then decreases as the annealing temperature rises further. The mechanism of the magnetic properties and magnetic variety should be attributed to the special structure of the nanowires∕AAO.
Effects of Annealing Temperature on Magnetic Property and Structure of Amorphous Co49Pt51 Alloy Nanowire Arrays Prepared by Direct-Current Electrodeposition

H Li,CL Xu,GY Zhao,HL Li

DOI: https://doi.org/10.1021/jp045347t

IF: 3.466

2005-01-01

The Journal of Physical Chemistry B

Abstract:Co49Pt51 nanowire arrays with an average diameter of 35 nm and lengths up to several micrometers were grown in an ordered porous anodic aluminum oxide (AAO) template using direct-current electrodeposition. The as-deposited samples were annealed at 100, 200, 300, 400, 500, 600, and 700 degrees C, respectively. The temperature dependence of the magnetic property of the Co49Pt51 nanowire arrays associated with the microstructure was analyzed by X-ray diffraction and a vibrating sample magnetometer. Magnetic measurements show that the samples both as-prepared and annealed at low temperatures have excellent perpendicular anisotropy. The perpendicular coercivity (Hc(perpendicular)) of Co49Pt51 alloy nanowire arrays increases dramatically as the annealing temperature (T(A)) rises, reaches a maximum(Hc(perpendicular) = 2770 Oe) at 400 degrees C, and then decreases sharply as T(A) rises further. This phenomenon should be attributed to the special structure of the nanowire arrays/AAO, and the microstructure factors significantly change during the annealing process.
Effects of Annealing at Ar Ambient on the Physical Properties of Zn0.66Co0.34O Thin Film

LIU Pu-cheng,QIU Dong-jiang

DOI: https://doi.org/10.3321/j.issn:1001-9731.2007.07.014

2007-01-01

Abstract:Zn0.66Co0.34O films were grown by reactive e-beam evaporation at 250℃ and then annealed in Ar ambient at 500℃ for 1h.Scanning electron microscope,X-ray diffraction(XRD) and vibrating sample magnetometer(VSM) were employed to characterize the microstructure and magnetic properties of Zn0.66Co0.34O film.XRD measurements revealed that both of as-grown and annealed Zn0.66Co0.34O films are homogeneous with a pure wurtzite structure.Room temperature M-H curves tested by VSM show that the as-grown film is superparamagnetic while the annealed film demonstrates a mixed magnetic characteristics of ferromagnetism and superparamagnetism.Such results suggest that by annealing treatment,some small crystal grains coalesced into relatively larger crystallites,whose sizes exceeded the superparamagnetic critical radius of Zn0.66Co0.34O material and correspondingly showed their ferromagnetic nature.However,probably duo to the fact that other grains still kept superparamagnetic,so the film emerged a mixed magnetic state of superparamagnetism and ferromagnetism.
Effect of Annealing Temperature on Soft Magnetic Characteristic and Microwave Magnetism of Nanocrystalline Fe_(52)Co_(26)Nb_6B_(15)Cu_1 Alloy

LIANG Di-fei,YU Zhi-hai,WANG Xin,HAN Man-gui,ZHOU Pei-heng

2010-01-01

Abstract:Fe_(52)Co_(26)Nb_6B_(15)Cu_1 alloy amorphous strip was prepared by the method of melt spin.After being heated at 480 ℃,500 ℃,550 ℃,600 ℃ and 650 ℃,the Fe_(52)Co_(26)Nb_6B_(15)Cu_1 alloy powder was successfully prepared by mechanical ball milling.After research on soft magnetic characteristic and microstructure which was changed with annealing temperature and tested by XRD,VSM,the micro-magnetic property of composite material was investigated by vector network analyzer in the frequency range of 500 MHz to 18 GHz.The results show that the microstructure and soft magnetic characteristic of Fe_(52)Co_(26)Nb_6B_(15)Cu_1 alloy sample can be controlled by annealing temperature and due to that,the complex permeability can be controlled in a large scale(μ′(2.0～4.2),μ″(1.0～2.5)).
Influence of Thermal Annealing on the Morphology and Magnetic Domain Structure of Co Thin Films

Muchan Li,Zhongzheng Tian,Xuemin Yu,Dachen Yu,Liming Ren,Yunyi Fu

DOI: https://doi.org/10.1088/2053-1591/abfeb2

IF: 2.025

2021-01-01

Materials Research Express

Abstract:Centimeter scale cobalt films with various thicknesses (8 nm ∼ 100 nm) were deposited by electron beam evaporation (EBE) and then annealed in a gas mixture of Ar and H2 at temperatures ranging from 200 °C to 500 °C. Advanced characterization techniques (e.g., XRD, SEM, AFM and MFM) were employed to investigate the influence of annealing on the morphology, crystal structures and magnetic domain structures of Co thin films. The results of SEM and AFM suggest that there is no obvious change in the morphology of Co film before and after annealing especially for thicker films and the root-mean-square roughness of Co film surface is slightly reduced after annealing. The influence of thermal annealing on the magnetic domain structure of EBE Co thin films was investigated by magnetic force microscopy (MFM) for the first time. It is found that even if there is no clear domain structure in the as-deposited films, it is possible to obtain periodic stripe domains with perpendicular magnetic anisotropy (PMA) by thermal annealing owing to the development of HCP Co phase, which was confirmed by XRD analysis. The correlations between the film morphology, thickness and magnetic domain structure are discussed qualitatively. Based on the periodic stripe magnetic domains, the domain-wall energy density of annealed cobalt films is calculated and this study found that the annealing has almost no effect on the energy density of the domain-wall. This work provides an effective way to obtain the perpendicular magnetic anisotropy (PMA) for practical applications.
The Effects of Composition and Thermal Treatment on the Magnetic Properties of Fe 100- X Co X Nanowire Arrays Based on AAO Templates

Lin Cao,Xinping Qiu,Jingbo Ding,Hulin Li,Liquan Chen

DOI: https://doi.org/10.1007/s10853-006-7181-8

IF: 4.5

2006-01-01

Journal of Materials Science

Abstract:A series of Fe 100- x Co x nanowire arrays with about 6.0 μm in length and 60 nm in diameter have been fabricated successfully by AC deposition of Fe and Co atoms into anodic aluminum oxide (AAO) templates. Samples with different composition could be obtained by adjusting the concentration ratio of Fe 2+ and Co 2+ in the solution of the electrolyte. The composition of the samples were determined by atomic absorption spectroscopy. Structural analysis was performed using scanning electron microscopy and X-ray diffraction. The magnetic properties of the samples were examined by vibrating sample magnetometry. The effects of composition and thermal treatment on the magnetic properties of the nanowire arrays have been examined. XRD shows that the nanowires have a body-centred-cubic (bcc) structure with a preferred orientation of the <110> axis parallel to the nanowires. When x is between 80 and 90, nanowires undergo a phase transformation α → γ which is very different from Fe–Co bulk alloy. Furthermore, a localized magnetization reversal mechanism of the nanowire arrays was conformed. It is also found that the magnetic properties of the arrays are critically dependent on the compositions and thermal treatment. With suitable choices of these factors, a kind of soft ferromagnetic film can be produced while maintaining a high coercivity and squareness.
Effect Of High Magnetic Field Annealing On Magnetic Properties Of Cofe2o4 Nanowire Arrays

Zhangben Wu,Bai Yang,Wupeng Cai,ZhiYu Zou,Ruihe Tang,He Jiang,Xiaofang Liu,MingJie Yang,Wei Liu,Ronghai Yu

DOI: https://doi.org/10.1109/TMAG.2011.2148105

IF: 1.848

2011-01-01

IEEE Transactions on Magnetics

Abstract:Cobalt ferrite (CoFe2O4) nanowire arrays with different diameters were prepared in porous anodic aluminum oxide (AAO) template by a sol-gel template method. A magnetic field annealing procedure was performed in the direction along wire axis (out of sample planes) at 600 degrees C under 10-T applied magnetic field to orient the spinel CoFe2O4 crystalline. The morphology was studied by scanning electron and transmission electron microscope. X-ray diffraction (XRD) patterns show that samples performed by the magnetic field annealing procedure have a texture along the nanowire axis, while those annealed without applied magnetic field show a nonoriented polycrystalline phase of spinel type structure. Vibration sample magnetometer (VSM) test shows the difference between CoFe2O4 nanowire arrays samples annealed with or without applied magnetic field. This difference shows the magneto-crystalline anisotropy with the easy magnetization direction along the nanowire axis, and is caused by the resultant effect of the easy magnetization direction distribution of the crystalline.
Annealing Influence on Magnetic Anisotropies of CoFe Thin Films

Weihua Zhu,Guanjie Wu,Hongwei Xue,Zhendong Zhu,Q. Y. Jin,Zongzhi Zhang

DOI: https://doi.org/10.1063/1.5079760

IF: 1.697

2019-01-01

AIP Advances

Abstract:Post-annealing effect on the magnetic anisotropies of cubic CoFe films epitaxially grown on MgO (001) substrates are investigated. X-ray diffraction patterns reveal that the crystallization degree gradually improves with the increase of annealing temperature (Ta), which results in obvious enhancement in both the uniaxial (HU) and biaxial magnetic anisotropy fields. Magnetic hysteresis loops of the unannealed sample show two equivalent easy axes along the CoFe [110] and [11¯0] directions, being in accord with the observed fourfold symmetry of angular remanent magnetization (ARM) curve. Nevertheless, with the increase of Ta, the two easy axis loops become inequivalent due to the increased HU along [110] direction, thus giving rise to a two-step switching behavior for the [11¯0] direction loop at Ta>350°C and the ARM curve transformation from fourfold to twofold symmetry. This work provides a deep insight and an effective approach to control the magnetic anisotropies and magnetization states for practical applications.
Geometry Dependence of the Annealing Effect on the Magnetic Properties of Fe48co52 Nanowire Arrays

HL Su,GB Ji,SL Tang,Z Li,BX Gu,YW Du

DOI: https://doi.org/10.1088/0957-4484/16/4/016

IF: 3.5

2005-01-01

Nanotechnology

Abstract:Highly ordered Fe48Co52 nanowire arrays with various interpore distances and diameters were fabricated by electrochemical deposition. The change of their magnetic properties after annealing has great dependences on the interpore distance and the wire diameter. The model of the prolate ellipsoid chain modified with the magnetostatic interaction is employed to explain this geometry dependence of the annealing effect. After annealing at 550 degrees C in H-2 atmosphere, good hard magnetic properties (at room temperature, coercivity H-c = 3.89 kOe, squareness M-r/M-s, = 0.954; at 78 K, H-c = 4.55 kOe, M-r/M-s = 0.954) were obtained in the arrays with a diameter of about 22 nm and an interpore distance of about 50 nm.
Effect of Annealing on the Magnetic Properties of FeCoNiCuNbSiB Soft Magnetic Alloys

Z. Li,K. F. Yao,T. C. Liu,X. Li,S. Wang

DOI: https://doi.org/10.3389/fmats.2021.805609

2022-01-05

Frontiers in Materials

Abstract:A series of nanocrystalline soft magnetic alloys with nominal compositions of Fe 66.8-x Co 10 Ni x Cu 0.8 Nb 2.9 Si 11.5 B 8 (x = 1–15 at%) were developed and studied. Effects of annealing on the soft magnetic properties, crystallization behavior, and domain structure were investigated. The alloys with higher Ni content were prone to exhibit stronger magnetic anisotropy. The Fe 66.8 Co 10 Ni 10 Cu 0.8 Nb 2.9 Si 11.5 B 8 alloy exhibited excellent soft magnetic properties, including the low permeability of 2000, low coercivity of about 0.6 A/m, and low remanence of 2.4 mT, together with a temperature gap of 128 K between two crystallization onset temperatures. It has been found that the Ni content and the annealing process possess significant effects on the soft magnetic property of the nanocrystalline alloys. It shows that the developed Fe 66.8 Co 10 Ni 10 Cu 0.8 Nb 2.9 Si 11.5 B 8 nanocrystalline alloy exhibits great potentials for applying in the field of common mode chokes or current transformers, due to its ability to resist the direct current.

materials science, multidisciplinary
Influence of Co on microstructure and coercivity of (Ni0.5Fe0.5)80B10Si2</s ub>Cu1Zr7 alloy

W. W. Sheng,Z. G. Qiu,Z. G. Zheng,X. Liu,D. C. Zeng

DOI: https://doi.org/10.1016/j.jnoncrysol.2021.120677

IF: 4.458

2021-01-01

Journal of Non-Crystalline Solids

Abstract:The effects of Co on microstructure, crystallization behavior and magnetic properties of (Ni0.5Fe0.5-xCox)(80)B10Si2Cu1Zr7 (x = 0 similar to 0.5) alloys were investigated. The results show that, the as-spun alloys remain lower coercivity (H-c) values (5 A/m similar to 14 A/m) over the whole Co content range, owing to their amorphous structure. After being annealed for 20 min above the onset temperatures of primary crystallization (T-x1), amorphous and nanocrystallines are coexisted in the alloys, and the crystal structure of nanocrystallines changes between fcc-(Ni, Fe, Co) and bcc-(Fe, Ni, Co) with the increasing Co content. In particular, it was found that H-c of the annealed alloys changes anomalously between 40 A/m and 1529 A/m with the increasing Co content, owing to the integrated action of grain size (D), magnetocrystalline anisotropy (K-1) and lattice distortion. Especially for the alloys with x = 0.2 and x = 0.3, serious lattice distortion is the dominant factor for their higher H-c value than 1000 A/m.
Effect of magnetic field annealing on soft magnetic properties for (Fe0.5Co0.5)73.5Cu1Nb3Si13.5B9 alloy

Rui-min Shi,Zhi Wang

DOI: https://doi.org/10.1007/s10854-021-05817-6

2021-04-03

Abstract:The effect of magnetic field annealing on crystallization and high-frequency/temperature soft magnetic properties is investigated for (Fe0.5Co0.5)73.5Cu1Nb3Si13.5B9 alloy. The applied magnetic field in the annealing process effectively facilitates the precipitation of ferromagnetic α-FeCo(Si) grains from the amorphous precursor and softens the magnetic properties, which are verified by the increase of crystalline volume fractions (Vcry) and the decrease of coercivity (HC), respectively. The initial permeability (μi) of sample annealed with applied field exhibits relatively higher value at elevated temperature, which is attributed to the intensive magnetic exchange coupling between the α-FeCo(Si) grains through the intergranular phase.

Effects of Ar/H-2 Annealing on the Microstructure and Magnetic Properties of Coo Nanoparticles

Effect of Second Annealing on Magnetic Properties and Microstructure of (nddy)fecocub Magnets

Effect of Annealing on the Microstructure and Magnetic Properties of Fe-based Nanocomposite Materials

Annealing and composition dependence of magnetic properties of Co-C nanocomposite thin films

Annealing Environment Effects on the Microstructure and Magnetic Properties of FePt–TiO2 and CoPt–TiO2 Nanocomposite Films

The Effect of Annealing on Microstructure and High Temperature Erosion Property of Arc-Spraying Coatings Containing Nanosized Ceramic Powders

Microstructure and phase dependence of magnetic properties of CoFeB nanowires

Effect of Annealing on the High Co-doped Ti1-xCoxO2 Magnetic Semiconductor

Microstructure, magnetic and magnetotransport properties of Co-C nanocomposite thin films

Effects of Annealing on the Structure and Magnetic Properties of Fe27co23pb50 Nanowire Arrays

Effects of Annealing Temperature on Magnetic Property and Structure of Amorphous Co49Pt51 Alloy Nanowire Arrays Prepared by Direct-Current Electrodeposition

Effects of Annealing at Ar Ambient on the Physical Properties of Zn0.66Co0.34O Thin Film

Effect of Annealing Temperature on Soft Magnetic Characteristic and Microwave Magnetism of Nanocrystalline Fe_(52)Co_(26)Nb_6B_(15)Cu_1 Alloy

Influence of Thermal Annealing on the Morphology and Magnetic Domain Structure of Co Thin Films

The Effects of Composition and Thermal Treatment on the Magnetic Properties of Fe 100- X Co X Nanowire Arrays Based on AAO Templates

Effect Of High Magnetic Field Annealing On Magnetic Properties Of Cofe2o4 Nanowire Arrays

Annealing Influence on Magnetic Anisotropies of CoFe Thin Films

Geometry Dependence of the Annealing Effect on the Magnetic Properties of Fe48co52 Nanowire Arrays

Effect of Annealing on the Magnetic Properties of FeCoNiCuNbSiB Soft Magnetic Alloys

Influence of Co on microstructure and coercivity of (Ni<sub>0.5</sub>Fe<sub>0.5</sub>)<sub>80</sub>B<sub>10</sub>Si<sub>2</s ub>Cu<sub>1</sub>Zr<sub>7</sub> alloy

Effect of magnetic field annealing on soft magnetic properties for (Fe0.5Co0.5)73.5Cu1Nb3Si13.5B9 alloy