Abstract:Electrochemical energy storage devices (EESDs) such as metal-air batteries (MABs) and alkaline electrolyte membrane fuel cells (AEMFCs) have begun to gain vast amounts of attention due to their high theoretical energy densities and open-circuit voltage values. Although these devices present promising aspects for the environment and sustainability, they suffer from the slow reaction kinetics and degradation effects that occur at the catalyst layer interface of the air electrode. Typically, these effects are due to the accumulation of molecular species such as water or oxygen at catalyst active sites because of poor electrode hydrophobicity and fluid management. Herein, we perform experimentation to mitigate these effects by implementing mixed carbon composite microporous layers onto porous carbon felt based air electrodes. This adaptation of the air cathode was predominantly based on the aforementioned downfalls and the lack of availability of commercial carbon felts that have adequate wet proofing and conductivity like some of the related carbon paper gas diffusion layers. Microporous layers (MPLs) enhance electrical conductivity, surface area, and adhesion at the catalyst layer and gas diffusion layer interface. These layers typically consist of a hydrophobic polymer such as polytetrafluoroethylene (PTFE) and a conductive carbon black substrate such as Ketjen Black 600JD (KJB). The incorporation of multi-walled carbon nanotube (MWCNT) and carbon black composites into the structure of the MPLs drastically decreases ohmic polarization with minimal increases in specific resistance. The electrical resistance of the synthesized carbon substrate decreases at high rates of MWCNT dispersion, which corresponds directly to a low MWCNT weight percentage within the composite. The MPL increases the mass transport through the electrode by mitigating flooding effects that typically occur within the pores near the surface of the catalyst layer, ultimately aiding in charge transfer between the gas diffusion layer and catalyst active sites. Preliminary data from AEMFC symmetric cell tests suggests that a microporous layer consisting of a 10 wt.% MWCNT/KJB (m/m) substrate is the optimal loading of carbon nanotubes and leads to better cell performance. There is an increase in current density of 60 mA/cm 2 compared to an air electrode with no MPL within the ohmic region of the polarization curve corresponding to approximately 0.7 V, while only an increase of 18 mA/cm 2 is seen for an MPL consisting of a 30 wt.% MWCNT/KJB (m/m) carbon substrate. The increase of charge transfer by the 10 wt.% synthesized carbon substrate MPL was attributed to the ability of the nanotubes at high rates of dispersion to act as molecular wires within the electrode. Additionally, zinc-air battery tests using the optimally configured air electrode, determined from previous experiments, show that the current density at an operating voltage of 1.1 V was increased by 2.3 times that of an electrode without an MPL using the same catalyst material and loading. Significantly, this research will lead to a better understanding of optimization of the air electrode used within electrochemical devices and how to eliminate some of the adverse effects associated with it. Figure 1

A new microporous layer material to improve the performance and durability of polymer electrolyte membrane fuel cells

Introducing Catalyst in Alkaline Membrane for Improved Performance Direct Borohydride Fuel Cells

Enhanced performance of proton exchange membrane fuel cells by Pt/carbon/antimony-doped tin dioxide triple-junction catalyst

Enhanced Proton Conductivities of Chitosan-Based Membranes by Inorganic Solid Superacid SO42−–TiO2 Coated Carbon Nanotubes

Amorphous Carbon Films Doped with Silver and Chromium to Achieve Ultra-Low Interfacial Electrical Resistance and Long-Term Durability in the Application of Proton Exchange Membrane Fuel Cells

(Digital Presentation) Evaluating the Performance of Multi-Walled Carbon Nanotube Composite Microporous Layers Deposited on Carbon Felt Gas Diffusion Layers

Anodic diffusion layer with graphene-carbon nanotubes composite material for passive direct methanol fuel cell

Improving of Micro Porous Layer based on Advanced Carbon Materials for High Temperature Proton Exchange Membrane Fuel Cell Electrodes

A design of gas diffusion media for polymer electrolyte membrane fuel cell: Characterization and water management investigation

Enhanced Cathode/Electrolyte Interface by a Nano-Modified Barrier Layer for Solid Oxide Fuel Cells

Titanate-Grafted Carbon Black-Facilitated MPLs for Advanced Proton Exchange Membrane Fuel Cells

Structural tailoring of the current collector/anode dual-layer hollow fibers to enhance the performance of micro-tubular protonic ceramic fuel cells

Optimizing proton exchange membrane fuel cell performance at low-humidity via constructing additional anodic water-retaining membrane layer containing sulfonated multi-walled carbon nanotubes

Durability of Alternative Metal Oxide Supports for Application at a Proton-Exchange Membrane Fuel Cell Cathode—Comparison of Antimony- and Niobium-Doped Tin Oxide

Janus nanofibers with multiple Li+ transport channels and outstanding thermal stability for all-solid-state composite polymer electrolytes

Ionomer Cross-Linking Immobilization of Catalyst Nanoparticles for High Performance Alkaline Membrane Fuel Cells

Titanium Carbide/carbon Nanofibers Film As Flexible Gas Diffusion Layers for Passive Direct Methanol Fuel Cells

High performance electrolyte-coated anodes for low-temperature solid oxide fuel cells: Model and Experiments

Superhydrophobic Carbon Functionalized by Chemical Grafting of Fluoroalkylsilane Enables an Efficient Microporous Layer for Proton-Exchange Membrane Fuel Cells

A First Principles And Experimental Study On The Influence Of Nitrogen Doping On The Performance Of Amorphous Carbon Films For Proton Exchange Membrane Fuel Cells

Effects of Anode Microporous Layers Made of Carbon Powder and Nanotubes on Water Transport in Direct Methanol Fuel Cells