Abstract:The decrease of both friction and wear is very crucial for reducing oil consumption and the associated environmental pollution. Accordingly, the search continues for novel materials, coatings, lubricants, and systems constituted by the aforementioned ones that can potentially reduce friction and wear. In this paper, a solid-liquid composite lubrication system was constituted by combining g-C3N4 nanosheets as the lubricating oil additives with Ti-DLC film, to achieve a green lubricant providing extreme anti-wear and friction reduction functionality. Tribological properties of the composite lubrication system with different concentrations of g-C3N4 were evaluated using a ball-on-disc sliding friction tester at different normal loads. The results show that both the friction coefficient and wear rate first decreases and then increases with the increase of the g-C3N4 concentration. The lubricant with 1 wt% g-C3N4 exhibits the optimal lubricant property with the friction coefficient of 0.076, 0.078 and 0.082, reducing by nearly 24%, 20%, and 12% compared with base oil for the normal loads of 50 N, 100 N, and 200 N, respectively. However, further increase in the concentration of g-C3N4 results in significant increase in the friction and wear of the tracks. The wear rates show no marked variation with the increasing load, indicating that g-C3N4 nanosheets possess a wide load adaptation range in wear-resistance. As environmentally friendly oil additives, g-C3N4 nanosheets can effectively improve the tribological property of the composite lubrication system. Based on the characterizations of both the Ti-DLC film and wear scars by SEM, XPS, non-contact 3D surface profiler and EDS, the synergistic lubrication mechanism of the g-C3N4 nanosheets and Ti-DLC film is also proposed.

Fabrication of the G-C3n4/Cu Nanocomposite and Its Potential for Lubrication Applications

Green Oil Additive G-C3n4: a Feasible Strategy to Enhance the Tribological Properties of DLC Film

Synthesis Of Reduced Graphene Oxide/Cu Nanoparticle Composites And Their Tribological Properties

Fabrication of two-dimensional MXene nanosheets loading Cu nanoparticles as lubricant additives for friction and wear reduction

The Synergistic Lubrication Effects of h-BN and g-C3N4 Nanoparticles as Oil-Based Additives for Steel/Steel Contact

Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

Effect of g-C3N4 morphology on its performance as lubricating additive for grease

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Development of Cu-15Ni-8Sn/MoS 2 self-lubricating composites with desirable mechanical and friction properties

Characterization and Tribological Properties of Graphene/Copper Composites Fabricated by Electroless Plating and Powder Metallurgy

Simple preparation of ultra‐thin white g‐C3N4 nano‐sheets and their use as nanofillers to enhance the tribological properties of epoxy composite coating

Research of Carbon Nanotubes-Cu Composite with Interpenetrating Networks

Fabrication of Novel CeO2/GO/CNTs Ternary Nanocomposites with Enhanced Tribological Performance

A molecular dynamics study of lubricating mechanism of graphene nanoflakes embedded in Cu-based nanocomposite

Study on the tribological properties of MoB/Cu laminated composite materials fabricated by hot-pressing process

Effect of nano-Cu-loaded graphene fillers on tribological properties of PTFE based composite coatings

Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites

Influences of B 4 C and carbon nanotubes on friction and wear performance of Cu base self-lubricating composite

Enhancing tribological properties of carbon-based films through catalytic Ni 3 C

Preparation of Ni-Cnt Composite Coatings on Aluminum Substrate and Its Friction and Wear Behavior

Tribological Performance of Nanocomposite Carbon Lubricant Additive