Abstract:Climate change issues and acid rain episodes have triggered new research directions and the conceptualization of new preventive approaches to reduce toxic gases from entering the environment. The reduction of carbon dioxide (CO2) levels in the indoor environment are also one of the challenging human safety issues during emergency incidents and rescues; for instance, a building fire. The use of an activated carbon fiber (ACF) based mask is not only effective to filter CO2 but it is also practically easy to use during such demanding situations. Such modified adsorbents will have high adsorption volume, fast adsorption rates and good thermal, acid and alkaline resistance properties. For the emergency mode considering fires, the major task is atmospheric recovery. Thus, CO2 concentration in the post-fire smoke could be high. The smoke in the room causes suffocations and unconsciousness leading to fatal injuries. In this study, ACF was modified using copper nitrate trihydrate [Cu (NO3)2 .3H2O] by impregnation and carbonization (450°C), followed by its characterization. The modified ACF (Cu-ACF-12) showed large surface area (1147m2 g−1), high micropore volume (0.45cm3 g−1) and an average pore size of 1.57nm. CO2 removal tests were carried out in a lab scale fixed bed adsorption column using the modified ACF. The process parameters were optimized based on a Box-Behnken Design (BBD) and tested in the following ranges: gas flow rate – 150–250mlmin−1, moisture content – 0–40% and modification of the ACF impregnated with copper (Cu) – 4–12wt.%. The experimental results were statistically interpreted to elucidate the main and interaction effects. The modification of ACF showed positive effects on CO2 removal, while gas flow rate and moisture content decreased the CO2 removal. Under the optimal conditions, (gas flow rate – 150mlmin−1, moisture content – 0% and modification of the ACF – 8%), CO2 removal capacity of 2.31mmol of CO2 g−1 Cu-ACF was obtained.

Preparation and Adsorption Property of Modified Activated Carbon for Purification of HCN in Closed Carbide Furnace Tail Gas

Removal of Hydrogen Cyanide by Using Activated Carbon: the Effect of Adsorption Condition and Chemical Modification

Hierarchical Porous Carbon As a Highly Efficient Adsorbent for Toluene and Benzene

Preparation of polyacrylonitrile-based activated carbon fiber for CS2 adsorption

CO<sub>2</sub> Adsorption Performance of Activated Coke Prepared from Biomass and Coal

Enhancement of CO2 Adsorption on High Surface Area Activated Carbon Modified by N2, H2 and Ammonia

Thermodynamic study of CO2 and N2 adsorption on modified activated carbon monolith

ADSORPTION OF PCBS IN FLUE GAS BY ACTIVATED CARBONS

Preparation of sludge-straw-based activated carbon and its adsorption of H2S

Coffee grounds derived N enriched microporous activated carbons: Efficient adsorbent for post-combustion CO2 capture and conversion

CO2 Adsorption Performance of Activated Coke Prepared from Biomass and Coal

Adsorption of organic pollutants from coking wastewater by activated coke

Catalytic Oxidation Removal of Hcn in Tail Gas

Preparation, characterization and adsorption performance of mesoporous activated carbon with acidic groups

Performance of CO2 Adsorption on Modified Activated Carbons Derived from Okara Powder Waste: Impacts of Ammonia Impregnation

Modification of activated carbon using urea to enhance the adsorption of dioxins

Preparation of K-N co-doped commercial cylindrical carbon via the coal partial steam gasification for CO2 adsorption

The adsorption properties of microporous activated carbon prepared from pistachio nut shell for low-concentration VOCs under low-medium temperatures

Adjusting the Porosity of Coal-Based Activated Carbons Based on a Catalytic Physical Activation Process for Gas and Liquid Adsorption

Activated carbon with excellent chromium(VI) adsorption performance prepared by acid–base surface modification

Effect of process parameters influencing the chemical modification of activated carbon fiber for carbon dioxide removal