Abstract:In this paper, mechanical properties and microstructures of the cast and extruded Al-xCu-1Li-0.4Mg–1Zn-0.1Zr alloys (x = 2.0, 3.0, 4.0, 4.5, 5.5, 6.5 wt%) were investigated. The results showed that the as-cast micrographs of alloys with different Cu content primarily consist of dendritic α-Al grains, and the intermetallic phases at the grain boundaries were Cu and Zr rich phases. After solution treatment, no recrystallization took place in extruded alloys, and the alloys mainly represented mixed textures composed of <111> and <100> fibers. Cu significantly affected the precipitation behavior of the extruded alloys. Only T1 (Al2CuLi) phases were observed in T6 (aging at 175 °C for 32 h) and T8 (3% pre-strain followed by aging at 150 °C for 32 h) treated alloy with 2 wt% Cu. Further increasing Cu contents (4.5 and 6.5 wt%) enabled the co-precipitation of T1 and θ' (Al2Cu) phases, as well as increased their density. In addition, the microstructures of grain boundaries of alloys with different Cu content showed dramatic differences. T1 phases precipitated at the grain boundaries of alloy containing 2 wt% Cu, while rare precipitation of T1 phases was observed at the grain boundaries of alloy with 6.5 wt% Cu. The yield strength (YS) of the alloys increased with the Cu content and the elongation (EL) showed an opposite trend. A good combination of ultra-high strength (YS = 684 MPa, ultimate tensile strength = 726 MPa) and ductility (EL = 6.3%) was obtained in T8 treated alloy containing 4.5 wt% Cu. The presence of the undesired coarse T2 (Al6CuLi3) phases at the grain boundaries resulted in the premature failure of the high Cu content alloys.

MICROSTRUCTURE AND WEAR PROPERTIES OF Al-Pb-Cu ALLOY SYNTHESIZED BY MECHANICALLY ALLOYING

Microstructure and Wear Properties of Al–Pb–Cu Alloys Prepared by Mechanical Alloying

Microstructure and Wear Properties of Al-Based Bearing Alloys Fabricated by Mechanical Alloying

Improvement of the Wear Behaviour of Al–Pb Alloys by Mechanical Alloying

Microstructure and wear properties of nanocomposite Al-Pb-Cu alloy cold-rolled onto steel matrix

Microstructural characteristics and mechanical properties of cast Al-3Li-xCu-0.2Zr alloy

Effect of Cu–Al Ratio on Microstructure and Mechanical Properties of Cu–Al Alloys Prepared by Powder Metallurgy

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Microstructure and Morphology of Al-Pb Bearing Alloy Synthesized by Mechanical Alloying and Hot Extrusion

The microstructures and mechanical properties of a highly alloyed Al-Zn-Mg-Cu alloy: The role of Cu concentration

Microstructural evolution and mechanical properties of cast Al‐2.6Li‐2.8Mg‐(0.5, 1.4)Cu‐0.2Zr‐0.2Sc alloys during heat treatment

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Study on Microstructure and Properties of Cu-Zr Alloy Prepared by Mechanical Alloying

Influence of Cu content on mechanical and tribological properties of Al–7Si–Cu alloy

Microstructure evolution and frictional wear behavior of Al‐18Si‐4Mg‐2Mn‐0.5Fe‐xCu alloys fabricated by laser additive manufacturing

Investigation on the microstructural evolution and corrosion behaviors of Zn-microalloyed Al-Cu-Li alloys

Wear Behavior of Al–Sn Alloys with Different Distribution of Sn Dispersoids Manipulated by Mechanical Alloying and Sintering

Promoting the High Load-Carrying Capability of Al–20 Wt%sn Bearing Alloys Through Creating Nanocomposite Structure by Mechanical Alloying

Microstructure Analysis for Al-Pb Alloy of Preparation in Powder Metallurgy Processing

Microstructure and Mechanical Properties of Al-5Cu-4.5Mg-2.5Zn Squeeze Cast Alloy

The Effect of Cu Addition and Milling Contaminations on the Microstructure Evolution of Ball Milled Al–Pb Alloy During Sintering