Abstract:Ytterbium (Yb) containing magnesium alloys have aroused extensive interest due to their excellent mechanical properties after thermomechanical processing and heat treatment. Unfortunately, the sole effect of Yb addition on the microstructure and mechanical properties of pure Mg matrix remains uncertain to date. In this work, the effects of Yb concentration on the texture development and tensile properties of pure Mg matrix during hot extrusion and the subsequent annealing were systematically investigated. The results revealed that the constitutional supercooling induced by Yb addition refined the as-cast microstructure but exerted a negligible effect on the original columnar grain morphology. When extruded at 300 °C, the dynamic recrystallization (DRX) process was considerably retarded. The in-grain misorientation axes (IGMA) analysis combined with TEM observation indicated that non-basal slips operated with increasing Yb concentration. Specifically, the prismatic 〈a〉 slip should be robustly activated in Mg–1.0 Yb extrudate, promoting the formation of the texture with {10–10} plane normal to the extrusion direction (ED), while for the Mg–2.0 Yb counterpart, the increased activity of pyramidal 〈c + a〉 slip and the relaxation of basal/<c + a> dislocations generated an ED-tilted texture component. The preferential grain growth dominated the subsequent annealing texture development at 400 °C when a comparable grain size was achieved. An obvious ED-tilted texture intensity with the peak around 〈–12–13〉 was observed in Mg–2.0 Yb alloy, which was primarily caused by grains with the basal orientation vanished and with the non-basal orientations intensified due to a higher concentration of Yb solute. Favored by the grain refinement, the Mg–2.0 Yb extrudate exhibited a high tensile yield strength of 304 ± 3.5 MPa, while the subsequently annealed counterpart presented a favorable elongation to failure of 14.8 ± 1.2%, which mainly due to the homogeneous grain structure, weak ED-tilted texture, and dissolution of coarse phases after high-temperature annealing.

Microstructures and Mechanical Properties of Extruded Mg–2Sn–xYb (x=0, 0.1, 0.5 At.%) Sheets

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Effect of Y content on microstructure evolution and tensile properties of Mg-8Li-3Al-2Sn-xY alloys

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Effects of Y on Microstructure and Mechanical Properties of Extruded Mg-5Al-1Ca Magnesium Alloys

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

Microstructures and Mechanical Properties of a High-Strength Mg-3.5Sm-0.6Zn-0.5Zr Alloy

Microstructure and Mechanical Properties of Extruded Mg-Zn-Nd-Y-Zr-Ca Alloy

Investigation on corrosion behavior and mechanical properties of an extruded Mg-Zn-Al-Sn-Mn alloy

Simulation on Microstructure Evolution and Mechanical Properties of Mg−Y Alloys: Effect of Trace Y

Microstructure and mechanical properties of as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY alloy with multi-precipitates

Microstructures and mechanical properties of as-extruded Mg–8Gd–2Y–1Zn–6Li alloy

Influence of Extrusion Ratio on Microstructure and Tensile Properties of Mg–Gd–Y–Zn–Zr Alloy

Texture development and tensile properties of Mg–Yb binary alloys during hot extrusion and subsequent annealing

Effect of yttrium addition on dynamic mechanical properties, microstructure, and fracture behavior of extrusion-shear ZC61 + xY (x = 0, 1, 2, 3) alloys

Effects of extrusion process on microstructure, precipitates and mechanical properties of Mg-Gd-Y-Zr-Ag alloys

Microstructure, Non-Basal Texture and Strength-Ductility of Extruded Mg-6Bi-3Zn Alloy

Effect of Sn content on microstructure and tensile properties of as-cast and as-extruded Mg−8Li−3Al−(1,2,3)Sn alloys

Effect of Sm content on microstructure and properties of extruded Mg-6Al-2Sr alloy