Abstract:Effects of temperature and strain rate on the fracture behaviors of an Al-Zn-Mg-Cu alloy are investigated by isothermal uniaxial tensile experiments at a wide range of temperatures and strain rates, from room temperature (RT) to 400 degrees C and from 10(-4) s(-1) to 10(-1) s(-1), respectively. Generally, the elevation of temperature leads to the increasing of elongation to fracture and the reduction of peak stress, while higher strain rate results in the decreasing of elongation to fracture and the increasing of peak stress. Interestingly, we found that the coefficient of strain rate sensitivity (m-value) considerably rises at 200 degrees C and work of fracture (W-f) fluctuates drastically with the increase of strain rate at RT and 100 degrees C, both of which signify a non-uniform and unstable deformation state below 200 degrees C. A competition of work hardening (WH) and dynamic recrystallization (DRX) exists at 200 degrees C, making it serve as a transitional temperature. Below 200 degrees C, WH is the main deformation mechanism of flow stress, and DRX dominates the flow stress above 200 degrees C. It has been found that from RT to 200 degrees C, the main feature of microstructure is the generation of dimples and microvoids. Above 200 degrees C, the coalescence of dimples and microvoids mainly leads to the failure of specimen, while the phenomenon of typically equiaxed dimples and nucleation appear at 400 degrees C. The observations of microstructure are perfectly consistent with the related macroscopic results. The present work is able to provide a comprehensive understanding of flow stress of an Al-Zn-Mg-Cu alloy at a wide range of temperatures and strain rates, which will offer valuable information to the optimization of the hot forming process and structural design of the studied alloy.

Temperature And Strain Rate Effects On The Strength And Ductility Of Nanostructured Copper

Modeling the Strain Rate-Dependent Constitutive Behavior in Nanotwinned Polycrystalline Metals

Strain hardening, strain rate sensitivity, and ductility of nanostructured metals

Strain Rate Dependence of Tensile Strength and Ductility of Nano and Ultrafine Grained Coppers

Strain Hardening and Strain Rate Sensitivity of Ultrafine-Grained Metals

An investigation of the combined size and rate effects on the mechanical responses of FCC metals

Enhanced Tensile Ductility and Toughness in Nanostructured Cu

Strain Rate Dependence of Tensile Ductility in an Electrodeposited Cu with Ultrafine Grain Size

Strain Rate Effects on Tensile Properties of Electrodeposited Nanocrystalline Cu

Strain Hardening and Large Tensile Elongation in Ultrahigh-Strength Nano-Twinned Copper

Influence of Specimen Dimensions on the Tensile Behavior of Ultrafine-Grained Cu

Tensile Ductility of Ultra-Fine Grained Copper at High Strain Rate

The effects of strain rate and temperature on the deformation behavior of the single-crystal copper nanowire

Compressive Behavior and Rate-Controlling Mechanisms of Ultrafine Grained Copper over Wide Temperature and Strain Rate Ranges

Influences of Strain Rate and Load Direction on the Thermo-Mechanical Behavior of A Nano-Alumina-Containing Copper Alloy Bar

Effects Of Temperature And Strain Rate On The Fracture Behaviors Of An Al-Zn-Mg-Cu Alloy

Temperature And Strain Rate Sensitivity Of Ultrafine-Grained Copper Under Uniaxial Compression

Experimental Investigation on Strain Rate Sensitivity of Ultra-Fine Grained Copper at Elevated Temperatures

Molecular dynamics simulations of tensile mechanical properties and microstructures of Al-4.5Cu alloy: the role of temperature and strain rate

Effect of cryogenic temperature on the deformation mechanism of a thin sheet of pure copper at the mesoscale

The Effect of Grain Size and Strain Rate on the Tensile Ductility of Bulk Nanostructured Metals and Alloys