Abstract:An equiatomic CoCrFeMnNi high-entropy alloy, which crystallizes in the face-centered cubic (fcc) crystal structure, was produced by arc melting and drop casting. The drop-cast ingots were homogenized, cold rolled and recrystallized to obtain single-phase microstructures with three different grain sizes in the range 4–160μm. Quasi-static tensile tests at an engineering strain rate of 10−3s−1 were then performed at temperatures between 77 and 1073K. Yield strength, ultimate tensile strength and elongation to fracture all increased with decreasing temperature. During the initial stages of plasticity (up to ∼2% strain), deformation occurs by planar dislocation glide on the normal fcc slip system, {111}〈110〉, at all the temperatures and grain sizes investigated. Undissociated 1/2〈110〉 dislocations were observed, as were numerous stacking faults, which imply the dissociation of several of these dislocations into 1/6〈112〉 Shockley partials. At later stages (∼20% strain), nanoscale deformation twins were observed after interrupted tests at 77K, but not in specimens tested at room temperature, where plasticity occurred exclusively by the aforementioned dislocations which organized into cells. Deformation twinning, by continually introducing new interfaces and decreasing the mean free path of dislocations during tensile testing (“dynamic Hall–Petch”), produces a high degree of work hardening and a significant increase in the ultimate tensile strength. This increased work hardening prevents the early onset of necking instability and is a reason for the enhanced ductility observed at 77K. A second reason is that twinning can provide an additional deformation mode to accommodate plasticity. However, twinning cannot explain the increase in yield strength with decreasing temperature in our high-entropy alloy since it was not observed in the early stages of plastic deformation. Since strong temperature dependencies of yield strength are also seen in binary fcc solid solution alloys, it may be an inherent solute effect, which needs further study.

Synergistic effects of temperature and strain rate on tensile properties of simulated Ni-6Cu alloy with Σ3 non-Arrhenius grain boundary

A Molecular Dynamics Study on Mechanical Performance and Deformation Mechanisms in Nanotwinned NiCo-based Alloys with Nano-Precipitates under High Temperatures

Effect of cyclic straining at elevated-temperature on static mechanical properties, microstructures and fracture behavior of nickel-based superalloy GH4145/SQ

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

Deformation and boundary motion analysis of a faceted twin grain boundary

The Effect of Strain Rate on the Tensile Deformation Behavior of Single Crystal, Ni-Based Superalloys

Molecular dynamics-based analysis of the effect of temperature and strain rate on deformation of nanocrystalline CoCrFeMnNi high-entropy alloy

Effects of Strain Rate, Temperature and Grain Size on the Mechanical Properties and Microstructure Evolutions of Polycrystalline Nickel Nanowires: A Molecular Dynamics Simulation

A Study of Grain Boundary Effects on the Stress-Induced Martensitic Transformation and Superelasticity in NiTi Alloy Via Atomistic Simulation

Strain Rate and Anisotropic Effects on Incipient Plastic Deformation of Zn–Cu–Ti Alloy Sheets

Effect of cross section and temperature on the Ni3Al precipitate on the tensile behavior through molecular dynamics simulation

Orientation and temperature dependence of yielding and deformation behavior of a nickel-base single crystal superalloy

Tension-compression asymmetry in Ni/Ni 3 Al interfaces: An atomistic investigation

Molecular Dynamics Simulation of Tensile Mechanical Properties of Ni/Ni<sub>3</sub>Al

Temperature and Strain Rate Dependent Mechanical Properties of a Square Nickel Plate with Different Shaped Central Cracks: A Molecular Dynamics Study

Molecular Dynamics Simulations of the Tensile Mechanical Response of Single Crystal/Polycrystalline Nickel

Effect of biphasic interface on mechanical properties and deformation mechanism of nickel base alloy

Real-time Atomic Deformation Behavior of Nano CoCrCuFeNi High-Entropy Alloy

The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy

In-situ EBSD study of deformation behavior of nickel-based superalloys during uniaxial tensile tests

Orientation dependence of microstructure deformation mechanism and tensile mechanical properties of Nickel-based single crystal superalloys: A molecular dynamics simulation