Abstract:TiCrAlN hard films based on TiN or CrN show superior properties in terms of hardness, wear resistance, and thermal stability due to the addition of alloying elements. AlCrTiN films based on AlN may have higher thermal shock properties, but the knowledge of AlCrTiN films with high Al content has been insufficient until now. In this study, two sets of AlCrTiN hard films with different Al contents of 48 at.% and 58 at.% among metal components were prepared via multi-arc ion plating so as to investigate the effect of Al content on the phase composition, hardness, and thermal shock resistance of the films. The same microstructures, morphologies, and thicknesses of the fabricated film samples were achieved by changing the combination of cathode alloy targets and adjusting the arc source current during deposition. The surface chemical composition, cross-sectional elemental distribution, microstructure, morphology, phase composition, surface hardness, film/substrate adhesion strength, and thermal shock performance of the AlCrTiN films were examined. The obtained results reveal that the two sets of AlTiCrN hard films are face-centered cubic solid solutions with a columnar fine grain structure and a preferred growth orientation of (200) crystal plane. The hardness of the AlCrTiN films can be improved up to HV2850 by properly reducing the Al content from 58 at.% to 48 at.%. Meanwhile, the film/substrate adhesion performance is strong enough in terms of critical loads greater than 200 N. Furthermore, the AlCrTiN films maintain high thermal shock resistance at 600 °C when the Al content decreases from 58 at.% to 48 at.%. The optimal composition of the AlCrTiN hard films is 25:13:15:47 (at.%), based on the consideration of hardness, adhesion, and thermal shock cycling resistance. This optimal AlCrTiN hard film can be suggested as an option for protective coatings of hot process die tools.

Preparation and Characterization of Al11cr4 Phase by Diffusion of Al/Cr Composite Film

Al-Cr Coatings Prepared by Diffusion at Low Temperature and Its Phase Characterization

Preparation of Al-Cr-Fe Coatings by Heat Treatment of Electrodeposited Cr/Al Composite Coatings

Effects of Heat Treatment on Structure Transformation of Cr/Al Composite Coatings

Preparation and Characterization of Α-Al2o3 Film by Low Temperature Thermal Oxidation of Al8Cr5 Coating

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

Preparation of Self-Healing Α-Al2o3 Film on Rapid Quenching Al-Cr Alloy by Thermal Oxidation at Low Temperature

Analysis on behaviors of contact reaction between quenched Al-Cr foils and stainless steel

Characterization of Aluminium Matrix Compositesreinforced by Al–Cu–Fe-Cr Quasicrystalline Particles

Study on Precipitation in (cocrfemnni)90al6ti4 High Entropy Alloy

Effect of annealing on the microstructure, mechanical and electrochemical properties of CrAlC coatings

Effects of Heat Treatments on Phase Structure of Electrodeposition Aluminum Coatings on Different Substrates

Phase Composition, Hardness, and Thermal Shock Properties of AlCrTiN Hard Films with High Aluminum Content

Preparation of Self-Healing Α-Al2o3 Films by Low Temperature Thermal Oxidation

Phase Composition of Heat-Resistant Layered Coatings of the Al–Cr–Ni System

Mechanical Properties and Microstructure of Al2O3/TiAl in Situ Composites Doped with Cr

Phase transformation and precipitation during solidification of FeCrAl alloy for automobile exhaust gas purifying systems

High Temperature Oxidation Behaviors of Al/Cr Composite Coating on Ti2AlNb Alloy

On the strengthening effect of Al-Cr-Si dispersoid in an Al-Si-Mg-Cu casting alloy with Cr addition

First-principles calculations, experimental study, and thermodynamic modeling of the Al-Co-Cr system

Analysis on phase transformation and lamellar formation of Ti-47.5Al-3Nb-1.5/3.5Cr alloys by confocal laser scanning in-situ observation