Abstract:TiCrAlN hard films based on TiN or CrN show superior properties in terms of hardness, wear resistance, and thermal stability due to the addition of alloying elements. AlCrTiN films based on AlN may have higher thermal shock properties, but the knowledge of AlCrTiN films with high Al content has been insufficient until now. In this study, two sets of AlCrTiN hard films with different Al contents of 48 at.% and 58 at.% among metal components were prepared via multi-arc ion plating so as to investigate the effect of Al content on the phase composition, hardness, and thermal shock resistance of the films. The same microstructures, morphologies, and thicknesses of the fabricated film samples were achieved by changing the combination of cathode alloy targets and adjusting the arc source current during deposition. The surface chemical composition, cross-sectional elemental distribution, microstructure, morphology, phase composition, surface hardness, film/substrate adhesion strength, and thermal shock performance of the AlCrTiN films were examined. The obtained results reveal that the two sets of AlTiCrN hard films are face-centered cubic solid solutions with a columnar fine grain structure and a preferred growth orientation of (200) crystal plane. The hardness of the AlCrTiN films can be improved up to HV2850 by properly reducing the Al content from 58 at.% to 48 at.%. Meanwhile, the film/substrate adhesion performance is strong enough in terms of critical loads greater than 200 N. Furthermore, the AlCrTiN films maintain high thermal shock resistance at 600 °C when the Al content decreases from 58 at.% to 48 at.%. The optimal composition of the AlCrTiN hard films is 25:13:15:47 (at.%), based on the consideration of hardness, adhesion, and thermal shock cycling resistance. This optimal AlCrTiN hard film can be suggested as an option for protective coatings of hot process die tools.

Phase Composition of Heat-Resistant Layered Coatings of the Al–Cr–Ni System

Al-Cr Coatings Prepared by Diffusion at Low Temperature and Its Phase Characterization

Effects of Heat Treatment on Structure Transformation of Cr/Al Composite Coatings

Effects of Heat Treatments on Phase Structure of Electrodeposition Aluminum Coatings on Different Substrates

Effects of High Al Content on the Phase Constituents and Thermal Properties in NiCoCrAlY Alloys

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

Preparation of Al-Cr-Fe Coatings by Heat Treatment of Electrodeposited Cr/Al Composite Coatings

FORMATION OF THE STRUCTURE AND COMPOSITION OF THE DIFFUSION INTERACTION ZONE DURING THE HEAT TREATMENT OF THE EXPLOSION-WELDED AD1 + Cr20Ni80 COMPOSITE IN THE PRESENCE OF A LIQUID PHASE

Structural State of High-Entropy Fe40–xNiCoCrAlx Alloys in High-Temperature Oxidation

Temperature-dependent evolution mechanism of interface microstructure between gradient MCrAlY coatings and nickel-based superalloy

Phase Composition, Hardness, and Thermal Shock Properties of AlCrTiN Hard Films with High Aluminum Content

Effect of Nickel Aluminide Microcrystalline Coating on High-Temperature Oxidation Behavior of NiAl-33.5%Cr-0.5%Zr Alloy

Experimental study and thermodynamic modeling of the Al-Co-Cr-Ni system

Influence of Layer Number and Thickness of CrAlYN/CrAlYO Coatings on Phase Composition, Structure and Properties

Interdiffusion mechanism at the interface between TiAl alloy and NiCoCrAlY bond coating

Clarifying the effects of composition and phase stabilization on the oxidation resistance in AlCoCrFeNiTi series high-entropy alloys at 1100 °C

Phase, Composition and Structure Changes of CoCrNi-Based Concentrated Alloys Resulting from High Temperature Oxidation

Comparative study of temperature-dependent oxidation and interdiffusion behavior on NiCoCrAlYHf-coated nickel-based single-crystal superalloys

Influence of Heat Treatment on the Microstructure and Wear Properties of Arc-Sprayed FeCrAl/Al Coating

Effects of heat treatments on the microstructure and hardness of thermally sprayed Ni-Cr-Mo-Al alloy coating

Al-Co-Cr-Fe-Ni high-entropy coatings produced by non-vacuum electron beam cladding: Understanding the effect of Al by in-situ synchrotron X-ray diffraction